1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. WPS54GU2
    5. /
  5. 8
Page 36 / 76 Scroll up to view Page 31 - 35
29
Wireless-G PrintServer for USB 2.0
Chapter 8: Bi-Admin Management
Bi-Admin Installation
5.
The
Choose Destination Location
screen will appear, as shown in Figure 8-3. Choose the location where the
B-Admin folder will be installed. To install the driver in the default location, click
Next
. If you want the folder
to be installed in a different location, click the
Browse
button and select the location. Then click
Next
.
Click
Back
to return to the previous screen. Click
Cancel
to end the Bi-Admin installation.
6.
The
Select Program Folder
screen, shown in Figure 8-4, will appear. An icon will be added to the program
folder listed. You may change the name for the program folder, if you wish. Click
Next
.
Click
Back
to return to the previous screen. Click
Cancel
to end the Bi-Admin installation.
7.
When the Bi-Admin is installed, the
Setup Complete
screen will appear. Click
Finish
.
Figure 7-4: Select Program Folder
Figure 7-3: Choose Destination Location
Downloaded from
www.Manualslib.com
manuals search engine
Page 37 / 76
30
Wireless-G PrintServer for USB 2.0
Chapter 8: Bi-Admin Management
Starting the Bi-Admin Management Utility
Starting the Bi-Admin Management Utility
1.
To start the Bi-Admin program, click
Start
,
Programs
,
Print Server Utility
, and then
Bi-Admin
Management Utility
. If the Bi-Admin Management Utility icon has been created, you can just double-click it
instead. You can drag the shortcut icon onto your Desktop for easy access to the Bi-Admin Management
Utility.
2.
When the Bi-Admin Management Utility appears, it will ask for the Connected Protocol. (See Figure 8-5.)
Make sure the box next to
TCP/IP
is checked. Click the
OK
button.
3.
The Bi-Admin Management Utility will automatically scan the network for the PrintServer. (See Figure 8-6.)
Figure 7-6: Searching for Device
Figure 7-5: Connected Protocol
Downloaded from
www.Manualslib.com
manuals search engine
Page 38 / 76
31
Wireless-G PrintServer for USB 2.0
Chapter 8: Bi-Admin Management
The Bi-Admin Management Utility
The Bi-Admin Management Utility
The
Bi-Admin Management Utility
screen will appear next. Any hardware found on the network will appear on the
left-hand side of the screen, as shown in Figure 8-7. The Utility can be managed from this screen. The menu and
icon options will be explained in this section.
Menu Options
Main
. The options are Device Status, Printer Status, Configure, Upgrade, Refresh, and Exit. These options are the
same as the icons that are displayed below the menu options (viewed from left to right), and are described below:
•
Device Status
. This option allows you to view all of the device settings, optionally save the device settings to
a file, or restore a previously saved file to the device.
If you click
Device Status
, the
Device Information
screen in Figure 8-8 will appear. A list of the PrintServer’s
device settings is displayed, including Hardware ID, Firmware version, Protocol ID, Default Name, Server
Name, and MAC Address. To save the information in a .txt (text) file, click the
Save to file
button.
To choose a different device that you configured, click the
Open
button. You may then browse for your file,
select it, and then click
Open
. The contents of the file will display on the right-hand side of the screen. To
save the file to the PrintServer, click
Restore to Device
.
Click the
Exit
button to return to the
Bi-Admin Management Utility
screen. For more information, click the
Help
button.
Figure 7-7: Bi-Admin Management Utility
Figure 7-8: Device Information
Downloaded from
www.Manualslib.com
manuals search engine
Page 39 / 76
32
Wireless-G PrintServer for USB 2.0
Chapter 8: Bi-Admin Management
The Bi-Admin Management Utility
•
Printer Status
. This option allows you to view the printer status, as well as set port and printer parameters.
If you click this option, a
Verify Password
screen will appear. Make sure that you enter the password in the
field before you click OK, or else an Incorrect Password message will appear. If the message appears, then
click
OK
. Enter the correct password in the field provided, and click
OK
again.
After the password has been successfully entered, the
Printer Status
screen will appear, as shown in Figure
8-10. The Device Name will be displayed and the Current Selected Port will be highlighted. The status
information for this port will be displayed.
Click the
Back
button to return to the
Bi-Admin Management Utility
screen. Click
Refresh
to refresh the
screen. For more information, click the
Help
button.
If the printer is bi-directional and not busy, the Printer Configuration
button will appear on the
Printer Status
screen. Click this button to view the printer’s Environmental Variable and Variable Value items. If the items
are not read-only, you can change them based on the options of your printer.
For more information, click the
Help
button.
Figure 7-9: Verify Password
Figure 7-10: Printer Status
Downloaded from
www.Manualslib.com
manuals search engine
Page 40 / 76
33
Wireless-G PrintServer for USB 2.0
Chapter 8: Bi-Admin Management
The Bi-Admin Management Utility
•
Configure
. You may configure the PrintServer with this option. If you click this option, a
Verify Password
screen will appear. Make sure that you enter the password in the field before you click OK, or else an
Incorrect Password message will appear. If the message appears, click
OK
. Enter the correct password in the
field provided, and click
OK
again.
After the password has been successfully entered, the
Configuration
screen will appear, as shown in Figure
8-12. It displays eight tabs: System, TCP/IP, AppleTalk, NetBEUI, Internet Printing, Port, Wireless, and SNMP.
The tabs will be described below.
System
•
Device Name
. Enter the Device Name in the field provided.
•
Comment
. Enter any comments in the
Comment
field.
•
Device Password
. To change the password, select
Change Device Password
, enter the new password
in the
Password
field, and then re-enter the password in the
Confirm Password
field.
•
Protocol
. Select the protocol you want to use for your network: TCP/IP, AppleTalk, NetBEUI, IPX/SPX.
Click the
Get Defaults
button if you want to cancel your changes and use the default settings.
When finished making your changes on this tab, click the
OK
button to save these changes, or click the
Cancel
button to undo your changes. For more information, click the
Help
button.
Figure 7-11: Verify Password
Figure 7-12: Configuration - System
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top