1. Home
    2. /
  2. Manuals
    3. /
  3. Inteno
    4. /
  4. X5671B
    5. /
  5. 5
Page 21 / 82 Scroll up to view Page 16 - 20
X5671
User’s Guide
16
Route
The Route Page of the device shows the route table. It contains Destination IP
address, Gateway, Subnet Mask, Flag, Metric, Service and Interface.
Figure 13: Device Route Table Information
ARP
The ARP Page of the device shows the ARP table mapping the IP address and
related MAC address. The ARP table contains IP address, Flag, MAC address,
Device Interface.
Figure 14: Device ARP Table Information
Page 22 / 82
X5671
User’s Guide
17
6
Advanced Setup
The Advance Setup menu includes the sub menus WAN, LAN, NAT, Security, Quality
of Service, Routing, DNS, and Port Mapping.
WAN
LAN
Security
Routing
DSL
Port Mapping
WAN
You can configure your internet connection from this page. This page displays the
details of existing internet connection. The device allows 1 bridge connection and 1
route connection existing at that same time without VLAN setting. But if you need
more than 1 bridge connection or 1 route connection, the VLAN tag is required.
Please refer below for more details. There are three connection types can be
configured including PPP over Ethernet (PPPoE), IP over Ethernet, and Bridging.
Figure 15: WAN Setup Page
To configure the WAN port, click Edit or Add to get the configuration pages. If there
are many services (protocols) in the single PVC interface, please enter the unique
VLAN tag number to identify the service (protocol).
Figure 16: WAN Port Configuration
Page 23 / 82
X5671
User’s Guide
18
To configure ATM PVC on the WAN interface:
Enter
VPI/VCI
values
Check to enable the
VLAN Mux
that allows multiple protocols in the same PVC
and then enter the
802.11Q VLAN ID
valued from 0 to 4095
Select the Service Category from the list (UBR without PCR, UBR with PCR,
CBR, Non Realtime VBR, Realtime VBR). Please leave it as default, UBR with
PCR, if ISP does not give you any information of this setting.
Check to enable the Qualify of Service if Service Category is UBR without PCR,
URB with PCR or Non Realtime VBR and you like this service.
Select the
Service Category from the list (UBR without PCR, UBR with PCR, CBR, Non
Realtime VBR, Realtime VBR). Please leave it as default, if ISP does not give
you any information of this setting.
Figure 17: Service Category Configuration
PCR
stands for Peak Cell Rate (ATM cells per second). It is the maximum
allowable rate which cells can be transferred in the connection.
SCR
stands for Sustainable Cell Rate (ATM cells per second). It is an average
allowable rate which cells can be transferred in the connection.
MRS
stands for Maximum Burst Size (ATM cells). It is the maximum allowable
burst size of cells which cells can be transferred in the connection.
Click
Next
to configure the Connection Type
Figure 18: WAN Connection Type Configuration
Global settings:
Check the
WAN protocol
from PPP over ATM (PPPoA), PPP over Ethernet
(PPPoE), MAC Encapsulation Routing (MER), IP over ATM (IPoA) and Briding.
Page 24 / 82
X5671
User’s Guide
19
Select the
Encapsulation Mode
from the list (LLC/SNAP-BRIDGING,
LLC/SNAP-Routing or VC/MUX)
Click
Next
PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE)
Figure 19: WAN Connection, PPPoA or PPPoE Configuration
To configure the PPPoA or PPPoE settings:
Enter the User’s PPP
Username
and
Password
Enter the
Service Provider Name
if any
Select the
Authentication Method
used during negotiation, default is AUTO.
Check “
Dial On Demand
” if you do not need PPPoA or PPPoE connection
always ON and enter the timeout value to disconnect the PPPoA or PPPoE
connection when connection is idle and timeout. If you enter “0”, zero for the
timeout value, it means always ON.
Check the “
IP extension”
if your ISP requests to enable it, otherwise do not
select it. This is a special service to forward IP address assigned by remote to
the local device in the LAN.
Check the “
Use Static IP address”
and enter the IP address if your ISP assigns
a fixed IP address to you. Otherwise, do not select it.
Check to enable “
Retry PPP Password on Authentication Error
”.
Check to enable “
PPP Debug Mode
”
This “
Bridge PPP frames between WAN and Local Ports
” is checked in default.
Click
Next
Page 25 / 82
X5671
User’s Guide
20
Figure 20: WAN Connection, PPPoA or PPPoE Configuration
NAT (Network Address Translation) setting:
Check to enable
NAT
that allows multiple PCs surfing Internet simultaneously
by using the same WAN IP address.
Check to enable
Firewall
Check to enable
IGMP Multicast
to avoid the multicast packet flooding to other
LAN ports where do not need this IGMP packet to get better efficiency in
Ethernet port.
Check to enable
WAN service
Enter the
Service Name
if you want to change it.
Click
Next
The
WAN Setup Summary
page shows all of parameters.
Figure 21: WAN Connection, PPPoA or PPPoE Configuration
Click
Save
if correct and click
Back
to restart the configuration again.

Rate

3.5 / 5 based on 2 votes.

Popular Inteno Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top