Page 21 / 95
Scroll up to view Page 16 - 20
EG101
User’s Guide
15
Route
The Route Page of the device shows the route table. It contains Destination IP
address, Gateway, Subnet Mask, Flag, Metric, Service and Interface.
Figure 10: Device Route Table Information
ARP
The ARP Page of the device shows the ARP table mapping the IP address and
related MAC address. The ARP table contains IP address, Flag, MAC address,
Device Interface.
Figure 11: Device ARP Table Information
DHCP
The DHCP Page of the device shows the DHCP table which DHCP server of device
assigns the IP address to the PC requesting an IP address. The DHCP table contains
Hostname, MAC address, IP address and Expired In.
Figure 12: Device DHCP Table Information
Page 22 / 95
EG101
User’s Guide
16
6
Advanced Setup
The Advance Setup menu includes the sub menus WAN, LAN, NAT, Security, Quality
of Service, Routing, DNS, and Port Mapping.
WAN
LAN
NAT
Security
QoS (Quality of Service)
Routing
DNS
Port Mapping
WAN
You can configure your internet connection from this page. This page displays the
details of existing internet connection. The device allows 1 bridge connection and 1
route connection existing at that same time without VLAN setting. But if you need
more than 1 bridge connection or 1 route connection, the VLAN tag is required.
Please refer below for more details. There are three connection types can be
configured including PPP over Ethernet (PPPoE), IP over Ethernet, and Bridging.
Figure 13: WAN Setup Page
To configure the WAN port, click Edit or Add to get the configuration pages. If there
are many services (protocols) in the WAN interface, please enter the unique VLAN tag
number to identify the service (protocol). Otherwise, please let is as unchecked as
default if you do not have any information from ISP about the VLAN settings.
Page 23 / 95
EG101
User’s Guide
17
Figure 14: WAN Port Configuration
To configure VLAN tag on the WAN interface:
Check the “
VLAN Mux – Enable Multiple Protocols Over WAN with 802.1Q
VLAN Tag”
Enter the unique
VLAN ID
Enter the
Mark of 802.1p
from 0 to 7
Click
Next
to configure the Connection Type
Figure 15: WAN Connection Type Configuration
Page 24 / 95
EG101
User’s Guide
18
Bridging
Figure 16: WAN Connection, Bridging Configuration
To configure the Bridging settings:
Check “
Enable Bridge Service
” to enable bridge service
Enter the
service name
for this bridging interface.
Click
Next
Figure 17: WAN Setup Summary
The
WAN Setup Summary
page shows all of parameters. Click
Save
if correct and
click
Back
to restart the configuration again.
Page 25 / 95
EG101
User’s Guide
19
PPP over Ethernet (PPPoE)
Figure 18: WAN Connection, PPPoE Configuration
To configure the PPPoE settings:
Enter the User’s PPP
Username
and
Password
Enter the
Service Provider Name
if any
Select the
Authentication Method
used during negotiation, default is AUTO.
Check “
Dial On Demand
” if you do not need PPPoE connection always ON and
enter the timeout value to disconnect the PPPoE connection when connection
is idle and timeout. If you enter “0”, zero for the timeout value, it means always
ON.
Check the “
IP extension”
if your ISP requests to enable it, otherwise do not
select it. This is a special service to forward IP address assigned by remote to
the local device in the LAN.
Check the “Use Static IP address” and enter the IP address if your ISP assigns
a fixed IP address to you. Otherwise, do not select it.
Check the “Retry PPP Password on Authentication Error” if necessary
Check to “Enable PPP Debug Mode” to get more debug message for analysis if
necessary
Click
Next
19216811.live