Huawei HG8247 Router Manual PDF (Setup & Configuration Guide)

Page 156 / 364 Scroll up to view Page 151 - 155

e.

Configure parameters of a WAN port.

a.

In the navigation tree, choose

WAN Device

>

WAN Device 1

>

WAN

Connection

. Select

WAN Connection

, right-click, and choose

Add PPP

Connection

from the shortcut menu.

b.

Select

WAN PPP Interface 1

and enter (or select) a proper value.

–

WAN Interface Name: ONT-HSI

–

WAN Enable: enable

–

Connection Type: IP_Routed

–

NATEnable: Enable (NAT must be enabled to configure the Internet

access service.)

–

Service Type: INTERNET (For configuring the Internet access service,

INTERNET

or a combination containing

INTERNET

needs to be

selected.)

–

VLAN ID: 10 (The VLAN ID of the ONT must be the same as the user-

side VLAN ID configured on the OLT.)

–

Priority: 1

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/

HG8447 GPON Terminal

Service Manual

3 Configuration

Issue 02 (2011-12-08)

Huawei Proprietary and Confidential

148

Page 157 / 364

f.

Configure a routing policy.

a.

In the navigation tree, choose

Layer 3 Forwarding

>

Policy Route

. Select

Policy Route

, right-click, and choose

Add

.

b.

Choose

Policy Route 1

and enter proper values.

–

Physical Port Name: LAN1

–

WAN Interface Name: WAN1(ONT-HSI)

NOTE

To bind a LAN port to a WAN port, set

Physical Port Name

and

WAN Interface

Name

. The preceding figure shows that WAN 1 is bound to LAN 1.

To bind a WAN port to multiple LAN ports, set

Physical Port Name

to

LAN1,...,LANx

. For example, to bind WAN 1 to LAN 1 and LAN 2, set

Physical Port

Name

to

LAN1,LAN2

.

g.

Click

OK

to complete the configuration of the new profile.

3.

Bind the value-added service profile.

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/

HG8447 GPON Terminal

Service Manual

3 Configuration

Issue 02 (2011-12-08)

Huawei Proprietary and Confidential

149

Page 158 / 364

a.

In the

Physical Map

navigation tree on the

Main Topology

tab page, double-

click the target OLT, or select the target OLT, right-click, and choose

NE

Explorer

.

b.

In the navigation tree, choose

GPON

>

GPON Management

.

c.

In the window on the right, choose

GPON ONU

.

d.

On the

GPON ONU

tab page, set the search criteria to find the GPON ONU

records.

e.

Select an ONT from the list, right-click, and choose

Bind VAS Profile

from the

shortcut menu. In the dialog box that is displayed, choose the created profile, and

click

OK

to complete profile binding.

4.

Configure the ONT value-added service.

a.

On the

GPON ONU

tab page, select an ONT, right-click, and choose

Configure

Value-Added Service

from the shortcut menu.

b.

Configure the user name and password for PPPoE dialup.

In the navigation tree, choose

WAN Device

>

WAN Device 1

>

WAN

Connection

>

WAN Connection 1

>

WAN PPP Interface

>

WAN PPP

Interface 1

. Select

WAN PPP Interface 1

, and set

User Name

to

iadtest@pppoe

and

Password

to

iadtest

. The user name and password must be

the same as those configured on the BRAS.

c.

Click

OK

. In the dialog box that is displayed, click

OK

. The configurations take

effect without the requirement of resetting the ONT.

----End

Result

The PC obtains the IP addresses automatically. After the PPPoE dialup is successfully performed

on the ONT, the PC can automatically obtain the IP addresses allocated by the ONT through

DHCP. Then, the Internet access service is provisioned after Websites are entered into Internet

Explorer (IE) address bars of the PC.

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/

HG8447 GPON Terminal

Service Manual

3 Configuration

Issue 02 (2011-12-08)

Huawei Proprietary and Confidential

150

Page 159 / 364

Configuration File

vlan 100 smart

vlan attrib 100 stacking

port vlan 100 0/19 0

dba-profile add profile-id 10 type4 max 102400

ont-lineprofile gpon profile-id 10

tcont 4 dba-profile-id 10

gem add 1 eth tcont 4

mapping-mode vlan

gem mapping 1 0 vlan 10

commit

quit

ont-srvprofile gpon profile-id 10

ont-port eth 4 pots 2 catv 1

commit

quit

interface gpon 0/1

port 1 ont-auto-find enable

display ont autofind 1

ont confirm 1 ontid 1 sn-auth 6877687714852900 omci ont-lineprofile-id 10 ont-

srvprofile-id 10ont confirm 1 ontid 2 sn-auth 6877687714852901 omci ont-lineprofile-

id 10 ont-srvprofile-id 10ont alarm-profile 1 1 profile-id 1

ont alarm-profile 1 2 profile-id 1

quit

traffic table ip index 8 cir 4096 priority 1 priority-policy tag-In-Package

service-port 1 vlan 100 gpon 0/1/1 ont 1 gemport 1 multi-service user-vlan 10 rx-

cttr 8 tx-cttr 8

service-port 2 vlan 100 gpon 0/1/1 ont 2 gemport 1 multi-service user-vlan 10 rx-

cttr 8 tx-cttr 8

queue-scheduler wrr 10 10 20 20 40 0 0 0

cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 6 cos7 7

save

3.3.4 Configuring the GPON FTTH VoIP Service (H.248 Protocol)

on the OLT CLI

The OLT is connected to the remote ONT through a GPON port to provide users with the IP-

based high-quality and low-cost VoIP service.

Service Requirements

l

The ONT is connected to the MGC through H.248.

l

The ONT obtains the IP address through DHCP.

l

Two phone sets are connected to two TEL ports of the ONT respectively, and calls can be

made between two phone sets.

l

Users of phone sets under different ONTs can call and communicate with each other.

l

The DBA mode of the VoIP service is assured bandwidth + maximum bandwidth, and no

rate limitation is performed on the upstream and downstream traffic.

Table 3-7

Data plan

Item

Data

OLT

S-VLAN ID: 200

S-VLAN type: smart VLAN

Upstream port: 0/19/0

C-VLAN ID: 20

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/

HG8447 GPON Terminal

Service Manual

3 Configuration

Issue 02 (2011-12-08)

Huawei Proprietary and Confidential

151

Page 160 / 364

Item

Data

ONT

ONT ID: 1 and 2

IP address of the MGC server: 200.200.200.200/24

Port ID of the MGC server: 2944

MG registration mode: domain name

MG domain name: 6877687714852901

Terminal IDs of line 1 and line 2: A0 and A1

Prerequisite

l

The interface data and the PSTN user data corresponding to the MG interface must be

configured on the MGC.

l

The OLT must be connected to the MGC. The IP address of the MGC server can be pinged

from the OLT.

l

For the ONT, to provision different voice services, you must select different software

versions. Before configuration, ensure that the ONT's version is V100R002C07.

Procedure

l

Configure the OLT.

1.

Create a service VLAN and add an upstream port to it.

The VLAN ID is 200, and the VLAN is a smart VLAN. Add upstream port 0/19/0 to

VLAN 200.

huawei(config)#

vlan 200 smart

huawei(config)#

port vlan 200 0/19 0

2.

(Optional) Configure upstream link aggregation.

In this example, a single upstream port is used. In the case of multiple upstream ports,

upstream link aggregation can be configured. For details, see Configuring Upstream

Link Aggregation.

3.

Enables ARP proxy.

For different users of the same SVLAN, because the service ports of the smart VLAN

are isolated from each other, the voice media streams cannot interchange normally.

Therefore, the ARP proxy function of the OLT needs to be enabled.

huawei(config)#

arp proxy enable

huawei(config)#

interface vlanif 200

huawei(config-if-vlanif200)#

arp proxy enable

huawei(config-if-vlanif200)#

quit

4.

Configure GPON ONT profiles.

GPON ONT profiles include the DBA profile, line profile, service profile, and alarm

profile.

–

DBA profile: A DBA profile describes the GPON traffic parameters. A T-CONT

is bound to a DBA profile for dynamic bandwidth allocation, improving the

upstream bandwidth usage rate.

–

Line profile: A line profile describes the binding between the T-CONT and the

DBA profile, the QoS mode of the traffic stream, and the mapping between the

GEM port and the ONT-side service.

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/

HG8447 GPON Terminal

Service Manual

3 Configuration

Issue 02 (2011-12-08)

Huawei Proprietary and Confidential

152

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share