Huawei HG8245T Router Manual PDF (Setup & Configuration Guide)

Page 291 / 429 Scroll up to view Page 286 - 290

Figure 4-15

DHCP Server Configuration

2.

Click

Apply

to apply the configuration.

Table 4-3

describes the parameters related to the DHCP server.

Table 4-3

Parameters related to the DHCP server

Parameter

Description

Enable primary DHCP server

Indicates whether to enable the primary

DHCP server. If the check box is selected,

you can set the primary DHCP server.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

4 Web Page Reference

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

283

Page 292 / 429

Parameter

Description

Enable DHCP L2 Relay

Indicates whether to enable the DHCP L2

Relay.

The DHCP relay is a process in which cross-

subnet forwarding of DHCP broadcast

packets is implemented between the DHCP

client and the DHCP server. In this manner,

the DHCP clients in different physical

subnets can obtain IP addresses which are

dynamically allocated from the same DHCP

server.

l

If

Mode

of the WAN port is

Route

, the IP

address of the ONT is obtained from

upper-layer DHCP servers in different

subnets and the user-side IP addresses are

obtained from the DHCP address pool of

the ONT.

l

If

Mode

of the WAN port is

Bridge

, the

ONT functions as a bridge. Thus, the ONT

does not have an IP address. The user-side

IP addresses are obtained from upper-

layer DHCP servers in different subnets.

Start IP Address

Indicates the start IP address in the IP address

pool on the primary DHCP server. It must be

in the same subnet as that of the IP address set

in "

LAN Host Configuration

". Otherwise,

the DHCP server fails to work normally.

End IP Address

Indicates the end IP address in the IP address

pool on the active DHCP server. It must be in

the same subnet as that of the IP address set

in "

LAN Host Configuration

". Otherwise,

the DHCP server fails to work.

Leased Time

Indicates the lease time of the IP address pool

on the active DHCP server. Options: minute,

hour, day, and week.

Enable secondary DHCP server

Indicates whether to enable the secondary

DHCP server. If the check box is selected,

you can set the secondary DHCP server.

IP Address

Indicates the IP address of the secondary

DHCP server.

Subnet Mask

Indicates the subnet mask of the secondary

DHCP server.

Start IP Address

Indicates the start IP address in the IP address

pool on the secondary DHCP server.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

4 Web Page Reference

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

284

Page 293 / 429

Parameter

Description

End IP Address

Indicates the end IP address in the IP address

pool on the secondary DHCP server.

Leased Time

Indicates the lease time of the IP address pool

on the secondary DHCP server. Options:

minute, hour, day, and week.

Option60

Indicates the option 60 field of the secondary

DHCP server. A user-side DHCP client can

obtain an IP address from the IP address pool

on the secondary DHCP server only when the

option 60 field carried by the user-side DHCP

client is the same as this setting.

4.4 WLAN

This topic describes how to perform basic and advanced configurations of the WLAN through

the Web page.

4.4.1 WLAN Configuration

1.

In the navigation tree on the left, choose

WLAN

>

WLAN Configuration

. In the pane on

the right, select the

Enable WLAN

option box. In the dialog box that is displayed, set the

basic Wi-Fi parameters, including the SSID, authentication mode, and encryption mode,

as shown in

Figure 4-16

.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

4 Web Page Reference

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

285

Page 294 / 429

Figure 4-16

WI-FI Basic Configuration

2.

Click

Apply

to apply the configuration.

Table 4-4

describes the basic Wi-Fi parameters.

Table 4-4

Basic Wi-Fi parameters

Parameter

Description

Enable WLAN

Indicates whether to enable the wireless network. The following

parameters can be set only when the wireless network is enabled.

SSID

Indicates the name of the wireless network. It is used to

differentiate different wireless networks. It consists of a

maximum of 32 characters, without space or Tab character.A

default SSID1, named

WirelessNet

is created after the creation

of an ONT. The system can configure up to four SSIDs at a time

and cannot assign IP addresses to Wi-Fi terminals by SSID.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

4 Web Page Reference

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

286

Page 295 / 429

Parameter

Description

Associated Device

Number

Specifies the number of STAs. It ranges from 1 to 32.

Broadcast Ssid

Indicates whether to enable or hide broadcast.

l

If the option box is selected, it indicates that the SSID

broadcast function is enabled. The ONT periodically

broadcasts the SSID, that is, the name of the wireless

network. In this way, any STA can search for the wireless

network.

l

If the option box is not selected, it indicates that the SSID

broadcast function is disabled. The SSID is hidden, and the

STA cannot search for the wireless network. The SSID can

be obtained only through a request.

WMM Enable

Indicates whether to enable the QoS of the wireless network.

After the function is enabled, the video and voice QoS can be

improved.

Authentication Mode

Indicates the authentication mode for the STA to request access

to the wireless network. The mode can be Open, Shared, WPA

Pre-Shared Key, WPA2 Pre-Shared Key, WPA Enterprise,

WPA2 Enterprise, or Wi-Fi Protected Setup.

It is set to open by default, that is, the STA can access the network

without authentication.

Encryption Mode

Indicates the encryption mode for the STA to request access to

the wireless network. The encryption mode and encryption

parameters vary with the authentication mode.

l

If the authentication mode is set to

Open

, the encryption

mode can be set to

None

or

WEP

.

l

If the authentication mode is set to

Shared

, the encryption is

WEP

.

l

If the authentication mode is set to

WPA Pre-Shared Key

,

WPA2 Pre-Shared Key

,

WPA Enterprise

, or

WPA2

Enterprise

, the encryption mode can be set to

AES

,

TKIP

,

or

TKIP&AES

.

l

If the authentication mode is set to

Wi-Fi Protected Setup

,

WPS Mode

must be set to

or

Push-button

.

NOTE

l

indicates the pin-based encryption.

l

Push-button

indicates the push-button-based encryption.

When

WPS Mode

is set to

Push-button

, press the

WPS

button on

the ONT and press the WPS icon included with the STA within two

minutes, or run the WPS setup program in the STA to install the WPS

software.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

4 Web Page Reference

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

287

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share