Huawei HG8245T Router Manual PDF (Setup & Configuration Guide)

Page 81 / 429 Scroll up to view Page 76 - 80

In the navigation tree, choose

Services

>

Voice Service

>

Voice Service 1

>

Interface configuration

>

Interface 1

>

H248

. Select

H248

and set

Domain

name

to

6877687714852901

.

NOTE

Domain Name

is ONT's domain name registered on the MGC. It is globally unique.

Domain

Name

in this example is ONT's SN.

(3)

Configure the terminal ID for the H.248 voice user.

In the navigation tree, choose

Services

>

Voice Service

>

Voice Service 1

>

Interface configuration

>

Interface 1

>

User

.

a.

Click

User 1

>

H248

and set

TID

to

A0

.

b.

Click

User 2

>

H248

and set

TID

to

A1

.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

73

Page 82 / 429

NOTE

The terminal IDs

A0

and

A1

must be consistent with the corresponding configuration on the

MGC.

(4)

Click

OK

. In the dialog box that is displayed, click

OK

. The configurations take

effect without the requirement of resetting the ONT.

----End

Result

Check whether the telephone functions properly. Connect two common telephones phone 1 and

phone 2 to two TEL ports on the ONT and test the dialing between phone 1 and phone 2. In

normal cases:

l

The caller hears the dialing tone after taking the phone off the hook.

l

When the caller dials the telephone number of the callee, the phone of the callee rings

successfully, and the caller hears the ring back tone.

l

The caller and the callee communicate with each other successfully.

l

After the callee hangs up, the caller hears the busy tone.

3.2.5 Configuring GPON FTTH Voice Service (SIP Protocol) on the

NMS

This topic describes how to configure the voice service when an ONT is connected to an OLT

through a GPON port.

Example Network

l

The phones connected to different ONTs can communicate with each other.

l

The ONT obtains an IP address in DHCP mode.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

74

Page 83 / 429

Figure 3-4

Configuring the GPON FTTH voice service (SIP protocol)

Phone1

OLT

Phone2

LAN Switch

U2000

ONT

Optical splitter

Procedure

l

Add the ONT to the U2000 in profile mode.

1.

Perform the following operations to add an MDU (not managed by the NAT

agent) that supports xPON upstream transmission.

(1)

On the topological navigation tree, select the required ODN under the OLT node.

Select the splitter under the ODN, right-click, and then choose

New

>

ONU

; or

select the splitter under the ODN, right-click the blank area on the

Physical

Root

interface on the right side, and then choose

New

>

ONU

.

(2)

On the interface that is displayed, set the parameters on the

Basic Parameters

and

Network Management Channel Parameters

tab pages (on this interface,

the ONU that supports the GPON upstream mode is considered as an example).

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

75

Page 84 / 429

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

76

Page 85 / 429

NOTE

l

When the OLT works in the profile mode, the ONU that supports the GPON upstream

mode needs to be bound with the GPON line profile.

l

When the OLT works in the distributed mode, the ONU that supports the GPON upstream

mode needs to be bound with the ONU capacity profile.

l

When the

OLT sets network management channel parameters

check box is cleared,

ONUs are configured and managed remotely on the OLT through the OMCI protocol.

l

When the

OLT sets network management channel parameters

check box is selected,

ONUs are configured and managed remotely on the OLT through the SNMP protocol.

l

Do not add the SNMP parameters on the ONU through the serial port, but issue the SNMP

profile from the OLT to the ONU only.

(3)

Click

OK

.

(4)

In the Main Topology, double-click the required OLT in the

Physical Root

navigation tree; or right-click the required OLT and choose

NE Explorer

from

the shortcut menu.

(5)

Choose

VLAN

from the navigation tree.

(6)

On the

VLAN

tab page, right-click and choose

Add

from the shortcut menu.

(7)

In the dialog box that is displayed, set the parameters.

–

VLAN ID: 4000

–

Type: Smart VLAN

(8)

Click

–

Click the

Upstream Port

tab and add upstream port 0/19/0 as the upstream

port of the VLAN.

–

Click the

L3 Interface

tab and set the parameters.

–

Configure L3 Interface: selected

–

IP Address: 192.168.50.4

(9)

Click

Finish

.

(10) Choose

GPON

>

GPON Management

from the navigation tree.

(11)

On the

GPON ONU

tab page, set the filter criteria or click

to display the

GPON ONUs.

(12)

In the information list, select the record where the shelf, slot, port, and ONU IDs

are 0, 2, 1, and 0 respectively and click the

ServicePort Info

tab in the lower

pane.

(13)

On the

ServicePort Info

tab page, right-click and choose

Add

from the shortcut

menu.

(14)

In the dialog box that is displayed, set the parameters.

–

Connection Type: LAN-GPON

–

VLAN ID: 4000

–

Interface Selection: 0/2/1/0/0

–

Service Type: Multi-Service VLAN

–

User VLAN: 4000

–

Keep the upstream and downstream settings the same: selected

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

77

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share