Huawei HG8245H Router Manual PDF (Setup & Configuration Guide)

Page 56 / 232 Scroll up to view Page 51 - 55

Figure 3-16

WI-FI Configuration

2.

Click

Apply

.

Table 3-5

describes the basic Wi-Fi parameters.

Table 3-5

Basic Wi-Fi parameters

Parameter

Description

Enable WLAN

Indicates whether to enable the wireless network. The following

parameters can be set only when the wireless network is enabled.

SSID

Indicates the name of the wireless network. It is used to

differentiate different wireless networks. It consists of a

maximum of 32 characters, without space or Tab character.

Associated Device

Number

Specifies the number of STAs. It ranges from 1 to 32.

3 Configuration Guide

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3-18

Huawei Proprietary and Confidential

Issue 02 (2011-01-26)

Page 57 / 232

Parameter

Description

Hide Broadcast

Indicates whether to enable or hide broadcast.

l

If the option box is not selected, it indicates that the SSID

broadcast function is enabled. The ONT periodically

broadcasts the SSID, that is, the name of the wireless

network. In this way, any STA can search for the wireless

network.

l

If the option box is selected, it indicates that the SSID

broadcast function is disabled. The SSID is hidden, and the

STA cannot search for the wireless network. The SSID can

be obtained only through a request.

WMM Enable

Indicates whether to enable the QoS of the wireless network.

After the function is enabled, the video and voice QoS can be

improved.

Authentication Mode

Indicates the authentication mode for the STA to request access

to the wireless network. The mode can be Open, Shared, WPA

Pre-Shared Key, WPA2 Pre-Shared Key, WPA Enterprise,

WPA2 Enterprise, or Wi-Fi Protected Setup.

It is set to open by default, that is, the STA can access the network

without authentication.

Encryption Mode

Indicates the encryption mode for the STA to request access to

the wireless network. The encryption mode and encryption

parameters vary with the authentication mode.

l

If the authentication mode is set to

Open

, the encryption

mode can be set to

None

or

WEP

.

l

If the authentication mode is set to

Shared

, the encryption is

WEP

.

l

If the authentication mode is set to

WPA Pre-Shared Key

,

WPA2 Pre-Shared Key

,

WPA Enterprise

, or

WPA2

Enterprise

, the encryption mode can be set to

AES

,

TKIP

,

or

TKIP&AES

.

l

If the authentication mode is set to

Wi-Fi Protected Setup

,

WPS Mode

must be set to

or

Push-button

.

NOTE

l

indicates the pin-based encryption.

l

Push-button

indicates the push-button-based encryption.

When

WPS Mode

is set to

Push-button

, press the

WPS

button on

the ONT and press the WPS icon included with the STA within two

minutes, or run the WPS setup program in the STA to install the WPS

software.

3.3.5 Security

This topic describes how to configure the IP address filter, MAC address filter, DoS, and ONT

access control through the Web page.

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3 Configuration Guide

Issue 02 (2011-01-26)

Huawei Proprietary and Confidential

3-19

Page 58 / 232

IP Filter Configuration

1.

Click the

Security

tab and then choose

IP Filter Configuration

from the navigation tree.

In the pane on the right, enable the IP address filter function. After selecting the filter mode,

click

New

. Then, in the dialog box that is displayed, configure the rule for filtering IP

addresses from the WAN interface to the LAN port, as shown in

Figure 3-17

.

Figure 3-17

IP Filter Configuration

2.

Click

Apply

.

The IP address filter function is a security mechanism configured on the residential gateway. It

enables or disables all or partial ports in an Intranet IP address segment to communicate with

all or partial ports in an Extranet IP address segment. The IP address filter configuration is used

to limit communication between an Intranet device and an Extranet device.

Table 3-6

describes the parameters related to the IP address filter.

Table 3-6

Parameters related to the IP address filter

Parameter

Description

IP address filter function

Indicates whether to enable the IP address filter function by

clicking

OPEN

or

CLOSE

.

Filter Mode

Indicates the IP address filter rule of the blacklist or whitelist.

l

Blacklist: indicates that the data meeting the rule in the filter

rule list is not allowed to pass.

l

Whitelist: indicates that the data meeting the rule in the filter

rule list is allowed to pass.

The filter mode is global config mode. Thus, the blacklist and

whitelist mode cannot be used at the same time.

3 Configuration Guide

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3-20

Huawei Proprietary and Confidential

Issue 02 (2011-01-26)

Page 59 / 232

Parameter

Description

Protocol

Indicates the type of the protocol, which may be TCP/UDP,

TCP, UDP, ICMP, or ALL.

LAN-side IP Address

Indicates the IP address on the LAN side.

LAN-side Port

Indicates the port ID on the LAN side. This parameter can be

configured when

Protocol

is set to

TCP/UDP

,

TCP

or

UDP

.

WAN-side IP Address

Indicates the IP address on the WAN side.

WAN-side Port

Indicates the ID of the WAN side port. This parameter can be

configured when

Protocol

is set to

TCP/UDP

,

TCP

or

UDP

.

MAC Filter Configuration

1.

Click the

Security

tab and then choose

MAC Filter Configuration

from the navigation

tree. In the pane on the right, after enabling MAC filter and selecting the filter mode, click

New

. On the dialog box that is displayed, configure the MAC filter rule for the PC to access

the Internet, as shown in

Figure 3-18

.

Figure 3-18

MAC Filter Configuration

2.

Click

Apply

.

The MAC address lists of PCs in the network are saved on the ONT. Configuring MAC filter

rules enables the PCs that conform to the rules to access the Internet service or disables the PCs

that do not conform to the rules to access the Internet service. A PC may have more than one IP

addresses but a unique MAC address. Therefore, configuring MAC filter rules effectively

controls the Internet service access rights of PCs in a LAN.

Table 3-7

describes the parameters related to the MAC filter.

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3 Configuration Guide

Issue 02 (2011-01-26)

Huawei Proprietary and Confidential

3-21

Page 60 / 232

Table 3-7

Parameters related to the MAC address filter

Parameter

Description

MAC address filter function

Indicates whether to enable the MAC address

filter function by clicking

OPEN

or

CLOSE

.

Filter Mode

Indicates the MAC address filter rule of the

blacklist or whitelist.

l

Blacklist: indicates that the data meeting

the rule in the filter rule list is not allowed

to pass.

l

Whitelist: indicates that the data meeting

the rule in the filter rule list is allowed to

pass.

The filter mode is global config mode. Thus,

the blacklist and whitelist mode cannot be

used at the same time.

Source MAC Address

Indicates the source MAC address in the

MAC address filter rule.

URL Filter Configuration

1.

Click the

Security

tab and then choose

URL Filter Configuration

from the navigation

tree. In the pane on the right, after enabling URL filter and selecting the filter mode, click

New

. On the dialog box that is displayed, configure the URL filter rule for the PC to access

the Internet, as shown in

Figure 3-19

.

Figure 3-19

URL Filter Configuration

2.

Click

Apply

.

3 Configuration Guide

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3-22

Huawei Proprietary and Confidential

Issue 02 (2011-01-26)

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share