Huawei EchoLife-HG8247 Router Manual PDF (Setup & Configuration Guide)

Page 151 / 364 Scroll up to view Page 146 - 150

NOTE

If multiple ONTs of the same type are connected to a port and the same line profile or service

profile is bound to the ONTs, you can add ONTs in batches by confirming the auto discovered

ONTs in batches to simplify the operation and increase the configuration efficiency. For

example, the preceding command can be modified as follows:

huawei(config-if-gpon-0/1)#

ont confirm 1 all sn-auth omci ont-

lineprofile-id 10 ont-srvprofile-id 10

c.

(Optional) Bind an alarm profile to the ONT.

In this example, bind the default alarm profile, namely alarm profile 1 to the

ONT.

huawei(config-if-gpon-0/1)#

ont alarm-profile 1 1 profile-id 1

huawei(config-if-gpon-0/1)#

ont alarm-profile 1 2 profile-id 1

5.

Confirm that the ONT goes online normally.

After an ONT is added, run the

display ont info

command to query the current status

of the ONT. Ensure that

Control flag

of the ONT is

active

,

Run State

is

online

,

Config state

is

normal

, and

Match state

is

match

.

huawei(config-if-gpon-0/1)#

display ont info 1 1

---------------------------------------------------------------------

F/S/P

:

0/1/1

ONT-ID

:

1

Control flag

:

active

//Indicates that the ONT is

activated.

Run state

:

online

//Indicates that the ONT goes online

normally.

Config state

:

normal

//Indicates that the configuration status

of the

ONT is normal.

Match state

:

match

//Indicates that the capability profile

bound to

the ONT is consistent with the

actual capability

of the ONT.

...//The rest of the response information is omitted.

If the ONT state fails, the ONT fails to be in the up state, or the ONT does not match,

check the ONT state by referring to the above-mentioned descriptions.

–

If

Control flag

is

deactive

, run the

ont activate

command in the GPON port mode

to activate the ONT.

–

If the ONT fails to be in the up state, that is,

Run state

is

offline

, the physical line

may be broken or the optical transceiver may be damaged. You need to check both

the material and the line.

–

If the ONT state fails, that is,

Config state

is

failed

, the ONT capability set

outmatches the actual ONT capabilities (For details about the ONT actual

capabilities, see Reference of GPON ONT Capability Sets). In this case, run the

display ont failed-configuration

command in the diagnosis mode to check the

failed configuration item and the failure cause. Then, rectify the fault according to

actual conditions.

NOTE

If an ONT supports only four queues, the values of 4–7 of the priority-queue parameter in the

gem add

command are invalid. After configuration recovers, Config state will be failed.

–

If the ONT does not match, that is,

Match state

is

mismatch

, the port types and

number of ports undermatch the actual port types and number of ports supported

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/

HG8447 GPON Terminal

Service Manual

3 Configuration

Issue 02 (2011-12-08)

Huawei Proprietary and Confidential

143

Page 152 / 364

by the ONT. In this case, run the

display ont capability

command to query the

actual capability of the ONT, and then select one of the following modes to modify

the ONT configuration:

–

Create a proper ONT profile according to the actual capability of the ONT, and

then run the

ont modify

command to modify the configuration data of the ONT.

–

Modify the ONT profile according to the actual capability of the ONT and save

the modification. Then, the ONT automatically recovers the configuration

successfully.

6.

Configure a traffic profile.

You can run the

display traffic table ip

command to query the traffic profiles existing

in the system. If the traffic profiles existing in the system do not meet the requirements,

you need to run the

traffic table ip

command to add a traffic profile.

The profile ID is 8, the CIR is 4 Mbit/s, the priority is 1, and packets are scheduled

according to the priority carried.

huawei(config-if-gpon-0/1)#

quit

huawei(config)#

traffic table ip index 8 cir 4096 priority 1 priority-

policy tag-In-Package

7.

Create service ports.

Set the service port indexes to 1 and 2, SVLAN ID to 100, GEM port ID to 1, and

CVLAN ID to 10. Use traffic profile 8.

huawei(config)#

service-port 1 vlan 100 gpon 0/1/1 ont 1 gemport 1 multi-

service user-vlan 10 rx-cttr 8 tx-cttr 8

huawei(config)#

service-port 2 vlan 100 gpon 0/1/1 ont 2 gemport 1 multi-

service user-vlan 10 rx-cttr 8 tx-cttr 8

8.

Configure the queue scheduling mode.

Use the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode, with the

weights of 10, 10, 20, 20, and 40 respectively; queues 5-7 adopt the PQ mode.

NOTE

Queue scheduling is a global configuration. You need to configure queue scheduling only once on

the OLT, and then the configuration takes effect globally. In the subsequent phases, you need not

configure queue scheduling repeatedly when configuring other services.

huawei(config)#

queue-scheduler wrr 10 10 20 20 40 0 0 0

Configure the mapping between queues and 802.1p priorities. Priorities 0-7 map

queues 0-7 respectively.

huawei(config)#

cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6

6 cos7 7

For the service board that supports only four queues, the mapping between 802.1p

priorities and queue IDs is as follows: priorities 0 and 1 map queue 1; priorities 2 and

3 map queue 2; priorities 4 and 5 map queue 3; priorities 6 and 7 map queue 4.

9.

Save the data.

huawei(config)#

save

l

Configure the optical network terminal (ONT) on the Web page.

Layer 3 route mode is used for connecting an ONT to the upper-layer device. IP addresses

of users' PCs are allocated by the DHCP IP address pool on the ONT. PPPoE auto dialup

is performed on the ONT. Parameters of the WAN port must be configured on the ONT.

1.

Log in to the Web configuration window.

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/

HG8447 GPON Terminal

Service Manual

3 Configuration

Issue 02 (2011-12-08)

Huawei Proprietary and Confidential

144

Page 153 / 364

a.

Configure the IP address of the PC network adapter to be in the same network

segment as the IP address of the local maintenance Ethernet port of the ONT

(default:

192.168.100.1

).

b.

Open the Web browser, and enter the IP address of the local maintenance Ethernet

port of the ONT.

c.

On the login window, enter the user name (default:

telecomadmin

) and password

(default:

admintelecom

) of the administrator. After the password authentication

is passed, the Web configuration window is displayed.

2.

Configure the working mode of a LAN port.

a.

In the navigation tree, choose

LAN

>

LAN Port Work Mode

. Select the check

box of LAN 1 and set LAN1 to work in the Layer 3 mode.

b.

Click

Apply

to apply the configuration.

3.

Configure parameters of a WAN port.

a.

In the navigation tree, choose

WAN

>

WAN Configuration

.

b.

In the right pane, click

New

. In the dialog box that is displayed, configure

parameters of a WAN port as follows:

–

WAN Connection: Enable

–

Service List: INTERNET (For configuring the Internet access service,

INTERNET

or a combination containing

INTERNET

needs to be selected.)

–

Mode: Route

–

VLAN ID: 10 (The VLAN ID of the ONT must be the same as the user-side

VLAN ID configured on the OLT.)

–

802.1p: 1

–

IP Acquisition Mode: PPPoE

–

NAT: Enable (NAT must be enabled to configure the Internet access service.)

–

User Name: iadtest@pppoe, Password: iadtest (The user name and password

must be the same as the user name and password configured on the BRAS.)

–

Binding options: LAN1

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/

HG8447 GPON Terminal

Service Manual

3 Configuration

Issue 02 (2011-12-08)

Huawei Proprietary and Confidential

145

Page 154 / 364

c.

Click

Apply

to apply the configuration.

4.

Save the configuration.

In the navigation tree, choose

System Tools

>

Configuration File

. In the right pane,

click

Save Configuration

to save the configuration.

5.

Check the ONT connection status.

In the navigation tree, choose

Status

>

WAN Information

. In the right pane,

Status

is

Connected

and the obtained IP address is displayed at

IP

.

l

Configure the ONT on the U2000.

Layer 3 route mode is used for connecting the ONT to the upper-layer device. IP addresses

of users' PCs are allocated by the DHCP IP address pool on the ONT. PPPoE auto dialup

is performed on the ONT. Parameters of the WAN port must be configured on the ONT.

The following uses batch configurations of creating a value-added service profile of the

ONT as an example. To configure an ONT, on the GPON ONU tab page, select an ONT,

right-click, and choose

Configure Value-Added Service

from the shortcut menu.

1.

Log in to the NMS (iManager U2000 V100R003C00) and start the FTP service.

2.

Configure the value-added service profile of the ONT.

a.

From the main menu, choose

Configuration

>

Access Profile Management

. In

the navigation tree of the tab page that is displayed, choose

PON Profile

>

ONT

VAS Profile

.

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/

HG8447 GPON Terminal

Service Manual

3 Configuration

Issue 02 (2011-12-08)

Huawei Proprietary and Confidential

146

Page 155 / 364

b.

On the

ONT VAS Profile

tab page, right-click, and choose

Add

from the shortcut

menu.

c.

In the dialog box that is displayed, set relevant parameters.

–

Profile Name: ONT-HSI

–

Vendor ID: HWTC(2011)

–

Terminal Type: 247

–

Version: V1R002C06-Later

d.

Configure the working mode of a LAN port.

In the navigation tree, choose

LANDevice

>

LAN Interface 1

>

LAN

Interface

>

LAN Ethernet Configuration 1

. Select

LAN Ethernet

Configuration 1

and set

LAN port two three-port enable

to

enable

(indicating

that LAN 1 works in the Layer 3 mode).

NOTE

l

If

LAN port two three-port enable

is

disable

, the LAN port works in the Layer 2

mode.

l

If

LAN port two three-port enable

is

enable

, the LAN port works in the Layer 3

mode.

LAN port two three-port enable

is defaulted to

disable

.

By default, the system has one

LAN Ethernet Configuration 1

node. To add nodes,

select

LAN Interface

, right-click, and choose

Add

from the shortcut menu.

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/

HG8447 GPON Terminal

Service Manual

3 Configuration

Issue 02 (2011-12-08)

Huawei Proprietary and Confidential

147

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share