1. Home
    2. /
  2. Manuals
    3. /
  3. Huawei
    4. /
  4. EchoLife-HG8247
    5. /
  5. 18
Page 86 / 364 Scroll up to view Page 81 - 85
NOTE
The terminal IDs
A0
and
A1
must be consistent with the corresponding configuration on the
MGC.
d.
Click
OK
. In the dialog box that is displayed, click
OK
. The configurations take
effect without the requirement of resetting the ONT.
----End
Result
Check whether the telephone functions properly. Connect two common telephones phone 1 and
phone 2 to two TEL ports on the ONT and test the dialing between phone 1 and phone 2. In
normal cases:
l
The caller hears the dialing tone after taking the phone off the hook.
l
When the caller dials the telephone number of the callee, the phone of the callee rings
successfully, and the caller hears the ring back tone.
l
The caller and the callee communicate with each other successfully.
l
After the callee hangs up, the caller hears the busy tone.
3.2.5 Configuring GPON FTTH Voice Service (SIP Protocol) on the
NMS
This topic describes how to configure the voice service when an ONT is connected to an OLT
through a GPON port.
Example Network
l
The phones connected to different ONTs can communicate with each other.
l
The ONT obtains an IP address in DHCP mode.
EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3 Configuration
Issue 02 (2011-12-08)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
78
Page 87 / 364
Figure 3-4
Configuring the GPON FTTH voice service (SIP protocol)
Phone1
OLT
Phone2
LAN Switch
U2000
ONT
Optical splitter
Procedure
l
Add the ONT to the U2000 in profile mode.
1.
Configure an MEF IP traffic profile.
a.
Choose
Configuration
>
Access Profile Management
from the main menu. In
the dialog box that is displayed, choose
Traffic Profile
from the navigation tree.
b.
Click the
MEF IP Traffic Profile
tab.
c.
Right-click and choose
Add Global Profile
from the shortcut menu.
d.
In the dialog box that is displayed, set the parameters.
–
Name: FTTx
EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3 Configuration
Issue 02 (2011-12-08)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
79
Page 88 / 364
–
CIR: 20480
–
Outer Priority: 1
e.
Click
OK
.
f.
In the information list, right-click the record and choose
Download to NE
from
the shortcut menu.
g.
In the dialog box that is displayed, select the required NE(s), and click
OK
.
2.
Configure a DBA profile.
a.
Choose
Configuration
>
Access Profile Management
from the main menu. In
the dialog box that is displayed, choose
PON Profile
>
GPON Profile
from the
navigation tree.
b.
Click the
DBA Profile
tab.
c.
Right-click and choose
Add Global Profile
from the shortcut menu.
d.
In the dialog box that is displayed, set the parameters.
–
Name: FTTx
–
T-CONT type: Maximum Bandwidth
–
Maximum Bandwidth: 32768
EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3 Configuration
Issue 02 (2011-12-08)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
80
Page 89 / 364
e.
Click
OK
.
f.
In the information list, right-click the record and choose
Download to NE
from
the shortcut menu.
g.
In the dialog box that is displayed, select the required NE(s), and click
OK
.
3.
Configure a line profile.
In a line profile, a GEM port can be bound to up to eight service streams. In a GEM
port, different GEM connections need to be set up for different service streams.
In this example, the mapping between GEM ports and MDU-side services is
implemented through VLANs, and the service streams of each service are mapped to
GEM port 1. In addition, different GEM connections are set up for the management
VLAN and the VLANs for the Internet, voice, and multicast services.
a.
Choose
Configuration
>
Access Profile Management
from the main menu. In
the dialog box that is displayed, choose
PON Profile
>
GPON Profile
from the
navigation tree.
b.
Click the
Line Profile
tab.
c.
Right-click and choose
Add Global Profile
from the shortcut menu.
d.
In the dialog box that is displayed, set the parameters.
–
Set
Name
to
FTTx
.
–
Choose
Base Info.
from the navigation tree and set the parameters.
–
Mapping Mode: VLAN
–
Qos Mode: Priority Queue
EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3 Configuration
Issue 02 (2011-12-08)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
81
Page 90 / 364
–
Right-click
T-CONT Info.
in the navigation tree and choose
ADD T-
CONT
from the shortcut menu. In the dialog box that is displayed, set the
parameters.
–
T-CONT Index: 1
–
DBA Profile: FTTx
–
Right-click
T-CONT1
in the navigation tree and choose
Add GEM Port
from the shortcut menu. In the dialog box that is displayed, set the parameters.
–
GEM Port Index: 1
–
Priority Queue: 1
EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3 Configuration
Issue 02 (2011-12-08)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
82

Rate

3.5 / 5 based on 2 votes.

Popular Huawei Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top