HooToo HT-ND003 Router Manual PDF (Setup & Configuration Guide)

Page 6 / 36 Scroll up to view Page 1 - 5

6

1.5

Physical Interfaces

There are three physical interfaces on the HooToo Powerline Adapter.

Note: If you press the Pair Button for more than 7 seconds, the extender

will disconnect from the network it is associated with. Please repair

again, and its network will restore.

2

Connecting

2.1

Connection Instruction

To ensure the optimum performance of the Powerline Adapter and to

significantly improve the transmission capacity of the network, we

recommend that you comply with the following connection rule:

Plug the HooToo Powerline Adapter directly into a wall socket (not a

multiple socket adapter).

Item

Description

Ethernet Port

Two 10/100Mbps Ethernet ports connected to a

PC LAN card or broadband device.

RST Port /

Reset Button

When the adapter is powered on, use a pin to

press and hold the Reset button for 10 seconds

until all LEDs go Off. When the Power LED turns on

and the Wi-Fi LED starts to blink rapidly, the reset

process is complete.

Power Plug

A power plug connected to any (100V

–

240V~,

50/60Hz) power socket.

Page 7 / 36

7

2.2

Hardware Connection

–

Computer

Please make sure that your PC can successfully access the Internet via

the router. Then connect the powerline devices by following the

instructions below.

Step 1: Connecting to the Internet

This section describes how to connect the HooToo Powerline Adapter

to your existing network.

Follow the procedures described below:

1. Connect one end of an Ethernet (RJ45) cable to the Ethernet port of

the powerline adapter or a compatible powerline adapter.

2. Connect the other end of the Ethernet (RJ45) cable to an available

Ethernet port of your wireless router.

3. Plug the powerline adapter or powerline extender into a wall socket.

4. Check and confirm the LEDs status. (The Power LED and Ethernet LED

on the powerline device should be ON).

The hardware connection mechanism is shown below:

Note:

Do not connect the powerline adapter to an extension lead, power

strip, extension cord, or surge protector, as these may degrade the

network performance.

Step 2:

Connecting To Your Computer

The following steps are needed to properly connect the powerline

adapter to your computer:

1. Connect one end of the provided Ethernet (RJ45) cable to the

powerline adapter

’s Ethernet port.

Page 8 / 36

8

2. Connect the other end of the Ethernet (RJ45) cable to your

computer’s LAN port.

3. Plug the powerline adapter into a wall socket next to the computer.

4. Turn on your computer.

5. Check and confirm that the Power LED and Ethernet LED on the

powerline adapter are ON.

The hardware connection mechanism is shown below:

As soon as the powerline devices are connected, a powerline network

is available.

Now the powerline adapter is ready for use for both wired and wireless

connections. No password is needed for the wired network

–

simply use

an Ethernet to connect to other devices. The default password for the

wireless connection is: 11111111 (

eight ones

).

Page 9 / 36

9

3

Configuring the Device

3.1

Log in to the Router

If the adapter is already connected to a network, you can access the

browser-based utility at: plc.hootoo.com.

Press “Enter”.

The system will automatically display the login page, please enter the

correct password. Click the Sign In button

（

Default password is

admin

）

Page 10 / 36

10

3.2

Quick Setup

Router:

The Ethernet port will behave as a WAN port for a wired

connection to an ADSL or Cable modem. The NAT routing will be

performed between the WAN and WLAN to make IP sharing possible.

WISP:

In this mode, the AP will behave as client. The router function will

also be added between the wireless WAN side and the Ethernet LAN

side. Therefore, the WISP subscriber can share the WISP connection

without the need for an extra router.

AP:

The most basic mode is Access Point. In this mode, the AP will act

as a central hotspot for different wireless LAN clients.

3.3

Router

In Router mode, a wired connection can be made to an ADSL or

Cable Modem via the WAN port to share the Internet to local wireless

and wired networks.

1. If you want to set the adapter in Router mode, choose Router, and

then click the

“

button.

Rate

Popular HooToo Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share