Page 6 / 71
Scroll up to view Page 1 - 5
4
WLAN ADSL2+ Router
2.2 Connectors
Table 2 shows the function of each connector and switch of the device.
Table 2. Function / Description of Connectors
Connector
Description
SWITCH
Power Switch
POWER
Connects to your WLAN ADSL2+ Router 12Vac power adaptor
LAN1~4
RJ-45 Jack (Ethernet Cable) connection to your PC, or HUB
LINE
Connects to your ADSL2+ line – for ADSL2+ Line input
RESET
Reset button. RESET the WLAN ADSL2+ Router to its default settings.
Press this button for at least 6 full seconds to start to reset it to its default
settings.
Figure1. Rear View of the WLAN ADSL2+ Router
Figure2. RESET button
Page 7 / 71
5
WLAN ADSL2+ Router
2.3 Factory Default Settings
Before configuration, please refer to following default settings,
Web interface:
Username: admin
Password: 1234
LAN IP Settings:
Subnet Mask: 255.255.255.0
DHCP:
DHCP Server: Enable
Page 8 / 71
6
WLAN ADSL2+ Router
3.0 Hardware Requirements
To use WLAN ADSL2+ Router, please have following hardware / accessories ready.
A PC with Pre-installed Ethernet Adapter (Required)
12Vac power adaptor (Included in the package)
RJ-45 Ethernet cable (Included in the package)
RJ-11cable (Included in the package)
3.1 Setting up the Hardware Environment
Please kindly refer to chapter 4.2 “Installation & Setup”
3.2 Powering on WLAN ADSL2+ Router
1.
Connect the power to the WLAN ADSL2+ Router by plugging the power supply into
an appropriate electrical outlet.
2.
If the Power LED is off, refer to “
Troubleshooting
” for information.
Please kindly refer to chapter 4.2 “Installation & Setup”
Note!
Be sure that you are well insulated from any power source to avoid
electricity shock.
Note!
Use only the manufacturer-approved power supply that shipped with the
WLAN ADSL2+ Router.
Page 9 / 71
7
WLAN ADSL2+ Router
4.0 System Requirements
1.
Pentium 200MHZ processor or above
2.
Windows 98SE / Windows Me / Windows 2000 / Windows XP / Windows Vista and
Windows 7
3.
64MB of RAM or above
4.
25MB free disk space
4.1 Package Contents
For Annex-B WLAN ADSL2+ Router
1. WLAN ADSL2+ Router
2.
CD-ROM (Software & Manual)
3. Quick Installation Guide
4.
1 x Telephone Cable (RJ-11)
5. Ethernet Cable (RJ-45)
6. Power Adaptor
7.
Annex-B Splitter (Optional, with an extra RJ-11 Telephone cable)
For Annex-A WLAN ADSL2+ Router
1. WLAN ADSL2+ Router
2.
CD-ROM (Software & Manual)
3. Quick Installation Guide
4.
1 x Telephone Cable (RJ-11)
5. Ethernet Cable (RJ-45)
6. Power Adaptor
7.
Annex-A Splitter (Optional, with an extra RJ-11 Telephone cable)
Page 10 / 71
8
WLAN ADSL2+ Router
4.2 Installation & Setup
Follow each STEP carefully and only go to the next step once you have completed the
previous STEP.
Connection of WLAN ADSL2+ Router
If you have an ISDN telephone line
connect the modem router as shown below:
1.
Connect the supplied RJ45 Ethernet cable from your PC's Ethernet port to any of the 4
WLAN ADSL2+ Router's LAN Ports.
2.
Connect the supplied RJ11 telephone cable from your home's telephone jack to the “
LINE
”
port of the supplied splitter. Connect another RJ11 telephone cable to the “
MODEM
” port
of the splitter and connect the other end of this cable to the LINE port of your WLAN
ADSL2+ Router.
(If there is no option Splitter, please connect the supplied RJ11 telephone
cable from your home's telephone jack to the “
LINE
” port of your WLAN ADSL2+ Router.)
3.
Connect a RJ11 telephone cable to the “
PHONE
” port of the splitter and connect the other
end to your telephone.
4.
Connect the power adapter to the power inlet “
POWER
” of the WLAN ADSL2+ Router and
turn the “
ON/OFF SWITCH
”
switch of your WLAN ADSL2+ Router on.
19216811.live