1. Home
    2. /
  2. Manuals
    3. /
  3. Hawking
    4. /
  4. HWRN1A
    5. /
  5. 4
Page 16 / 138 Scroll up to view Page 11 - 15
7
1-5 Product Overview
Top Panel
LED Name
Light Status
Description
PWR
ON
Router is switched on and correctly powered
Wireless
On
Wireless network is switched on or WPS
mode is on.
Off
Wireless network is switched off
Flashing
Wireless LAN activity (transferring or
receiving data).
Internet
10/100M
On
WAN port (Internet) is running at 100Mbps
Off
WAN port (Internet) is running at 10Mbps
Flashing
WAN activity (transferring or receiving data)
Internet
LNK/ACT
On
WAN port is connected
Off
WAN port is not connected
Flashing
WAN activity (transferring or receiving data)
LAN
10/100M
On
LAN port is running at 100Mbps
Off
LAN port is running at 10Mbps
LAN
LNK/ACT
On
LAN port is connected
Off
LAN port is not connected
Flashing
LAN activity (transferring or receiving data)
Page 17 / 138
8
Back Panel
Item Name
Description
Antenna A to C
All are 3dBi dipole antennas.
Power
Power connector, connects to A/C power adapter.
Reset
Reset the router to factory default settings (clear all settings).
Press this button and hold for 10 seconds to restore all settings to
factory defaults.
LAN (1 – 4)
Local Area Network (LAN) ports 1 to 4.
MODEM
Wide Area Network (WAN / Internet) port.
Antenna A
Antenna B
Antenna C
Page 18 / 138
9
Chapter II: System and Network Setup
2-1 Build network connection
Please follow the following instructions to build the network connection
between your new WIRELESS router and your computers and other
network devices:
1.
Connect your xDSL / cable modem to the WAN port of router by
Ethernet cable.
2.
Connect all your computers and network devices (network-enabled
consumer devices other than computers, like game console, or switch /
hub) to the LAN port of the router.
3.
Connect the A/C power adapter to the wall socket, and then connect it
to the ‘Power’ socket of the router.
Page 19 / 138
10
4.
Please check all LEDs on the front panel. ‘PWR’ LED should be
steadily on, WAN and LAN LEDs should be on if the computer /
network device connected to the respective port of the router is
powered on and correctly connected. If PWR LED is not on, or any
LED you expected is not on, please recheck the cabling, or jump to
‘4-2 Troubleshooting’
for possible reasons and solutions.
Page 20 / 138
11
2-2 Connecting to wireless broadband router by web browser
After the network connection is built, the next step you should do is
setup the router with proper network parameters, so it can work properly
in your network environment.
Before you can connect to the router and start configuration
procedures, your computer must be able to get an IP address
automatically (use dynamic IP address). If it’s set to use static IP address,
or you’re unsure, please follow the following instructions to configure
your computer to use dynamic IP address:
If the operating system of your computer is….
Windows 95/98/Me
- please go to section 2-2-1
Windows 2000
- please go to section 2-2-2
Windows XP
- please go to section 2-2-3
Windows Vista
- please go to section 2-2-4
2-2-1 Windows 95/98/Me IP address setup:
1.
Click ‘Start’ button (it should be located at lower-left corner of your
computer), then click control panel. Double-click
Network
icon, and
Network
window will appear. Select ‘TCP/IP’, then click ‘Properties’.

Rate

4.5 / 5 based on 2 votes.

Popular Hawking Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top