Hawking HWRN1A Router Manual PDF (Setup & Configuration Guide)

Page 61 / 138 Scroll up to view Page 56 - 60

52

2-6-2 DHCP Server:

These settings are only available when ‘DHCP Server’ in ‘LAN IP’

section is ‘Enabled’, and here are descriptions of every setup item:

Lease Time (1):

Please choose a lease time (the duration that every

computer can keep a specific IP address) of every

IP address assigned by this router from dropdown

menu.

Start IP (2):

Please input the start IP address of the IP range.

End IP (3):

Please input the end IP address of the IP range.

Domain Name (4):

If you wish, you can also optionally input the

domain name for your network. This is optional.

Recommended Value if you don’t know what to fill:

Lease Time: Two Weeks (or ‘Forever’, if you have less than 20 computers)

Start IP: 192.168.1.100

End IP: 192.168.1.200

Domain Name: (leave it blank)

NOTE:

1. The number of the last field (mentioned ‘d’ field) of ‘End IP’ must be

greater than ‘Start IP’, and can not be the same as router’s IP address.

2. The former three fields of IP address of ‘Start IP’, ‘End IP’, and ‘IP

Address of ‘LAN IP’ section (mentioned ‘a’, ‘b’, and ‘c’ field) should be

the same.

3. These settings will affect wireless clients too.

1

3

4

2

Page 62 / 138

53

2-6-3 Static DHCP Leases Table:

This function allows you to assign a static IP address to a specific

computer forever, so you don’t have to set the IP address for a

computer, and still enjoy the benefit of using DHCP server. A

maximum of 16 static IP addresses can be assigned here.

(If you set ‘Lease Time’ to ‘forever’ in ‘DHCP Server’ section, you can

also assign an IP address to a specific computer permanently, however,

you will not be able to assign a certain IP address to a specific

computer, since IP addresses will be assigned in random order by this

way).

Here are descriptions of every setup item:

Enable Static

Check this box to enable this function,

DHCP Leases (1):

otherwise uncheck it to disable this function.

MAC Address (2):

Input the MAC address of the computer or

network device (total 12 characters, with

characters from 0 to 9, and from a to f, like

‘001122aabbcc’)

IP address (3):

Input the IP address you want to assign to this

computer or network device

‘Add’ (4):

After you inputted MAC address and IP address

pair, click this button to add the pair to static

DHCP leases table.

1

2

3

4

Page 63 / 138

54

If you want to remove all characters you just entered, click ‘Clear’.

After you clicked ‘Add’, the MAC address and IP address mapping

will be added to ‘Static DHCP Leases Table’ section.

If you want to delete a specific item, please check the ‘Select’ box of a

MAC address and IP address mapping (1), then click ‘Delete Selected’

button (2); if you want to delete all mappings, click ‘Delete All’ (3). If

you want to deselect all mappings, click ‘Reset (4).

After you finish all LAN settings, please click ‘Apply’ button on the

bottom of this page. After you click ‘Apply’, the following message will

be displayed on your web browser:

Please click ‘Continue’ to go back to previous setup menu; to continue on

router setup, or click ‘Apply’ to reboot the router so the settings will take

effect (Please wait for about 30 seconds while router is rebooting).

1

2

3

4

Page 64 / 138

55

2-7

Wireless LAN Configuration

If your computer, PDA, game console, or other network devices which

is equipped with wireless network interface, you can use the wireless

function of this router to let them connect to Internet and share

resources with other computers with wired-LAN connection. You can

also use the built-in security functions to protect your network from

being intruded by malicious intruders.

Please follow the following instructions to set wireless parameters:

Please click ‘Wireless’ tab at the top of web management interface, and

the following message will be displayed on your web browser. You must

enable wireless function of this router, or the wireless interface of this

router will not function. Please select ‘Enable’ (1), then click ‘Apply’ (2)

button.

If you’re coming here because you want to disable wireless function,

please select ‘Disable’ (3), then click ‘Apply’ (2) button.

After you click ‘Apply’, the following message will be displayed on your

web browser:

1

2

3

Page 65 / 138

56

Please click ‘Continue’ to go back to previous setup menu; to continue on

other setup procedures, or click ‘Apply’ to reboot the router so the

settings will take effect (Please wait for about 30 seconds while router is

rebooting).

2-7-1 Basic Wireless Settings

Please click ‘Basic Setup’ menu at the top of web management interface,

then click ‘Basic Settings’, and the following message will be displayed

on your web browser:

This wireless router can work in 6 modes:

a.

AP

: Standard wireless AP (access point).

b.

Station-Infrastructure

: Configure the router to Ethernet devices such as

TV, Game player, HDD & DVD to enable the Ethernet device to be a

wireless station.

c.

AP Bridge-Point to Point

: Connect this router with another wireless

router, to expand the scope of network.

d.

AP Bridge-Point to Multi-Point

: Connect this router with up to four

other wireless routers, to expand the scope of network.

1

2

3

4

5

Rate

Popular Hawking Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share