Hawking HWRN1A Router Manual PDF (Setup & Configuration Guide)

Page 71 / 138 Scroll up to view Page 66 - 70

62

Here are descriptions of every setup items:

Band (2)

Select the band you want to use, two wireless

routers must use the same setting.

Channel

Select the channel you want to use, two wireless

Number (3)

routers must use the same setting.

MAC

address (4)

Input the MAC address of another wireless router.

Set

Click to set security settings for this connection

Security (5)

(Please go to section ‘2-7-3 Wireless Security’

for detailed instructions).

2-7-1-4 Setup procedure for ‘AP Bridge-Point to Multi-Point’:

In this mode, you can connect your wireless router with at least four

wireless routers to expand the scope of wireless network, and all clients

(wired only – AP will not accept wireless clients in this mode) of the

wireless routers will think they’re on the same physical network.

1

2

3

4

5

6

7

8

Page 72 / 138

63

Here are descriptions of every setup items:

Band (2)

Select the band you want to use, all the wireless

routers must use the same setting.

Channel

Select the channel you want to use, all the wireless

Number (3)

routers must use the same setting.

MAC address

Input the MAC address of other wireless routers.

1 to 4 (4 - 7)

Set

Click to set security settings for this connection

Security (8)

(Please go to section ‘2-7-3 Wireless Security’

for detailed instructions).

2-7-1-5 Setup procedure for ‘AP Bridge – WDS’

In this mode, you can expand the scope of network by combining up to

four other access points together, and every access point can still accept

wireless clients.

NOTE: For WDS mode, the output signal nature is the same as that of

normal AP mode.

Page 73 / 138

64

Here are descriptions of every setup items:

Band (2)

Select the band you want to use, all the wireless

routers must use the same setting.

ESSID (3)

Input the ESSID of your wireless router, the setting

should be the same with other wireless routers for

the convenience of roaming.

Channel

Select the channel you want to use, all the wireless

Number (4)

routers must use the same setting.

Associated Clients

Click ‘Show Active Clients’ button, then an “Active

Wireless Client Table” will pop up. You can see the

status of all active wireless stations that are

connecting to the access point.

1

2

3

4

5

7

8

6

9

10

Page 74 / 138

65

MAC address

Input the MAC address of other wireless routers.

1 to 4 (6 - 8)

Set

Click to set security settings for this connection

Security (9)

(Please go to section ‘2-7-3 Wireless Security’ for

detailed instructions).

2-7-1-6 Setup procedure for ‘Universal Repeater’

In this mode, the router can act as a wireless repeater; it can be Station

and AP at the same time. It can use Station function to connect to a Root

AP and use AP function to service all wireless stations within its

coverage.

1

2

3

4

5

7

6

NOTE: For Repeater Mode, this router will demodulate the received

signal, checking if this signal is noise for the operating network then

have the signal modulated and amplified again. The output power of

this mode is the same as that of WDS and normal AP mode.

Page 75 / 138

66

Here are descriptions of every setup items:

Band (2)

Select the band you want to use, all the wireless

routers must use the same setting.

ESSID (3)

This is the name of wireless router. You can type any

alphanumerical characters here, maximum 32

characters. ESSID is used to identify your own

wireless router from others when there are other

wireless routers in the same area. Default SSID is

‘default’, it’s recommended to change default ESSID

value to the one which is meaningful to you, like

myhome, office_room1, etc.

Channel

Select the channel you want to use, all the wireless

Number (4)

clients must use the same setting.

Associated Clients (5): Click ‘Show Active Clients’ button, then an

“Active Wireless Client Table” will pop up. You can

see the status of all active wireless stations that are

connecting to the access point.

Root AP SSID (6):

In ‘Universal Repeater’ mode, this device can act as

a station to connect to a Root AP. You should assign

the SSID of the Root AP here or click ‘Select Site

Survey’ button to choose a Root AP.

Site Survey (10):

Click ‘Select Site Survey’ button, then a “Wireless

Site Survey Table” will pop up. It will list all

available access points near by. You can select one

access point in the table and the router will join

wireless LAN through this access point.

After you finish the wireless setting, please click ‘Apply’ button, after

you click ‘Apply’, the following message will be displayed on your web

browser:

Rate

Popular Hawking Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share