Page 26 / 131 Scroll up to view Page 21 - 25
25
Input ‘ipconfig’, then press ‘Enter’ key. Please check the IP address followed
by ‘Default Gateway’ (In this example, the IP address of router is
192.168.2.1,
please note that this value may be different.
)
3. Connect the router’s management interface by web browser
After your computer obtained an IP address from router, please start your
web browser, and input the IP address of router in address bar. The following
message should be shown:
NOTE: If the IP address of Gateway is not displayed, or the address followed
by ‘IP Address’ begins with ‘169’, please recheck network connection
between your computer and router, and / or go to the beginning of this
chapter, to recheck every step of network setup procedure.
Page 27 / 131
26
Please input user name and password in the field respectively, default user
name is ‘admin’, and default password is ‘1234’, then press ‘OK’ button, and
you can see the web management interface of this router:
NOTE: If you can’t see the web management interface, and you’re
being prompted to input user name and password again, it means you
didn’t input username and password correctly. Please retype user
name and password again. If you’re certain about the user name and
password you type are correct, please go to ‘4-2 Troubleshooting’ to
perform a factory reset, to set the password back to default value.
TIP: This page shows the four major setting categories: QuickSetup,
General Setup, Status, and Tools. You can find the shortcut which
leads to these setting categories at the upper-right corner of every
page, and you can jump to another category directly by clicking the
link, and don’t have to go back to the first page.
Page 28 / 131
27
2-3 Using ‘Quick Setup’
This router provides a ‘Quick Setup’ procedure, which will help you to
complete all required settings you need to access the Internet in very short
time. Please follow the following instructions to complete the ‘Quick Setup’:
Please go to QuickSetup menu by clicking ‘QuickSetup’ button.
And the following message will be displayed:
1. Set Time Zone
Here are descriptions of every setup items:
HERE!
Page 29 / 131
28
Set Time
Please press
button, a drop-down list
Zone:
will be shown, and you can choose a time zone of the
location you live.
Time Server
Input the IP address / host name of time server
Address:
here
Daylight
If the country you live uses daylight saving,
Savings:
please check ‘Enable Function’ box, and choose the
duration of daylight saving.
After you finish with all settings, please click ‘Apply’ button.
2. Broadband Type
Please choose the broadband (Internet connection) type you’re using in this
NOTE: There are several time servers available on internet:
129.6.15.28 (time-a.nist.gov)
132.163.4.101 (time-a.timefreq.bldrdoc.gov)
131.107.1.10 (time-nw.nist.gov)
If you found that the time of router is incorrect, try another time server.
Page 30 / 131
29
page. There are six types of Internet connection, they are:
Cable Modem
- Please go to section 2-3-1
Fixed-IP xDSL
- Please go to section 2-3-2
PPPoE xDSL
- Please go to section 2-3-3
PPTP xDSL
- Please go to section 2-3-4
L2TP xDSL
- Please go to section 2-3-5
Telstra Big Pond
- Please go to section 2-3-6
If you’re not sure, please contact your Internet service provider. A wrong
Internet connection type will cause connection problem, and you will not be
able to connect to internet.
If you want to go back to previous step, please press ‘Back’ button on the
bottom of this page.
NOTE: Some service providers use ‘DHCP’ (Dynamic Host
Configuration Protocol) to assign IP address to you. In this case, you
can choose ‘Cable Modem’ as Internet connection type, even you’re
using another connection type, like xDSL. Also, some cable modem
uses PPPoE, so you can choose ‘PPPoE xDSL’ for such cable modem
connection, even you’re using a cable modem.

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top