Page 126 / 794
Scroll up to view Page 121 - 125
Vigor2860 Series User’s Guide
112
Details Page for IPv6 – 6in4 Static Tunnel in WAN1/WAN2
This type allows you to setup 6in4 Static Tunnel for WAN interface.
Such mode allows the router to access IPv6 network through IPv4 network.
However, 6in4 offers a prefix outside of 2002::0/16. So, you can use a fixed endpoint rather
than anycast endpoint. The mode has more reliability.
Available settings are explained as follows:
Item
Description
Remote Endpoint IPv4
Address
Type the static IPv4 address for the remote server.
6in4 IPv6 Address
Type the static IPv6 address for IPv4 tunnel with the value
for prefix length.
LAN Routed Prefix
Type the static IPv6 address for LAN routing with the value
for prefix length.
Tunnel TTL
Type the number for the data lifetime in tunnel.
After finished the above settings, click
OK
to save the settings.
Page 127 / 794
Vigor2860 Series User’s Guide
113
Below shows an example for successful IPv6 connection based on 6in4 Static Tunnel mode.
Details Page for IPv6 – 6rd in WAN1/WAN2
This type allows you to setup 6rd for WAN interface.
Available settings are explained as follows:
Item
Description
6rd Mode
Auto 6rd –
Retrieve 6rd prefix automatically from 6rd
service provider. The IPv4 WAN must be set as "DHCP".
Static 6rd -
Set 6rd options manually.
IPv4 Border Relay
Type the IPv4 addresses of the 6rd Border Relay for a given
6rd domain.
IPv4 Mask Length
Type a number of high-order bits that are identical across
all CE IPv4 addresses within a given 6rd domain.
It may be any value between 0 and 32.
Page 128 / 794
Vigor2860 Series User’s Guide
114
6rd Prefix
Type the 6rd IPv6 address.
6rd Prefix Length
Type the IPv6 prefix length for the 6rd IPv6 prefix in
number of bits.
After finished the above settings, click
OK
to save the settings.
Below shows an example for successful IPv6 connection based on 6rd mode.
Page 129 / 794
Vigor2860 Series User’s Guide
115
3.1.4 Multi-PVC/VLAN
This router allows you to create multi-PVC for different data transferring for using. Simply go
to
WAN
and select
Multi-PVC/VLAN
page.
General
The system allows you to set up to eight channels which are ready for choosing as the first
PVC line that will be used as multi-PVC.
Available settings are explained as follows:
Item
Description
Channel
Display the number of each channel.
Channels 1 and 2 are used by the Internet Access web user
interface and can not be configured here.
Channels 5 ~ 10 are configurable.
Enable
Display whether the settings in this channel are enabled
(Yes) or not (No).
WAN Type
Displays the physical medium that the channel will use.
VPI/VCI
Display the value for VPI and VCI.
VLAN Tag
Displays the VLAN tag value that will be used for the
packets traveling on this channel.
Port-based Bridge
The network traffic flowing on each channel will be
identified by the system via their VLAN Tags. Channels
using the same WAN type may not configure the same
VLAN tag value.
Enable
- Check this box to enable the port-based bridge
function on this channel.
P1 ~ P6
– Check the box(es) to build bridge connection on
LAN.
Page 130 / 794
Vigor2860 Series User’s Guide
116
Click any index (8~10) to get the following web page:
Available settings are explained as follows:
Item
Description
Multi-VLAN Channel
8/9/10
Enable –
Click it to enable the configuration of this
channel.
Disable –
Click it to disable the configuration of this
channel.
WAN Type
The connections and interfaces created in every channel
may select a specific WAN type to be built upon. In the
Multi-PVC application, only the Ethernet WAN type is
available. The user will be able to select the physical WAN
interface the channel shall use here.
General Settings
VPI
- Type in the value provided by your ISP.
VCI
- Type in the value provided by your ISP.
Protocol
- Select a proper protocol for this channel.
Encapsulation
- Choose a proper type for this channel. The
types will be different according to the protocol setting that
you choose.
19216811.live