Page 176 / 202
Scroll up to view Page 171 - 175
Vigor2800 Series User’s Guide
170
Settings in the remote host:
1.
For Win98/ME, you may use "Dial-up Networking" to create the PPTP tunnel to Vigor
router.
For Win2000/XP, please use "Network and Dial-up connections" or “Smart
VPN Client”, complimentary software to help you create PPTP, L2TP, and L2TP over
IPSec tunnel. You can find it in CD-ROM in the package or go to
www.draytek.com
download center. Install as instructed.
2.
After successful installation, for the first time user, you should click on the
Step 0.
Configure
button. Reboot the host.
3.
In
Step 2. Connect to VPN Server
, click
Insert
button to add a new entry.
If an IPSec-based service is selected as shown below,
Page 177 / 202
Vigor2800 Series User’s Guide
171
You may further specify the method you use to get IP, the security method, and
authentication method. If the Pre-Shared Key is selected, it should be consistent with
the one set in VPN router.
If a PPP-based service is selected, you should further specify the remote VPN server IP
address, Username, Password, and encryption method. The User Name and Password
should be consistent with the one set up in the VPN router. To use default gateway on
remote network means that all the packets of remote host will be directed to VPN
server then forwarded to Internet. This will make the remote host seem to be working
in the enterprise network.
Page 178 / 202
Vigor2800 Series User’s Guide
172
4.
Click
Connect
button to build connection. When the connection is successful, you will
find a green light on the right down corner.
4.3 QoS Setting Example
Assume a teleworker sometimes works at home and takes care of children. When working
time, he would use Vigor router at home to connect to the server in the headquater office
downtown via either HTTPS or VPN to check email and access internal database.
Meanwhile, children may chat on VoIP or Skype in the restroom.
1.
Make sure the QoS Control on the left corner is checked. And select BOTH in
Direction
.
2.
Enter the Class Name of Index 1. In this index, she will set reserve bandwidth for
Email using protocol POP3 and SMTP. Click
Basic
button on the right.
3.
Select POP3 and SMTP on the left column and add to right column. Click OK to exit.
Page 179 / 202
Vigor2800 Series User’s Guide
173
4.
Enter the Class Name of Index 2. In this index, she will set reserve bandwidth for
HTTPS. And click Basic button on the right.
5.
Select HTTPS in the list on the left column and click on ADD to add to right column.
Click OK to exit.
6.
Check the Enable UDP Bandwidth Control on the bottom to prevent enormous UDP
traffic of VoIP influent other application.
7.
If the worker has connected to the headquater using host to host VPN tunnel. (Please
refer to Chapter 3 VPN for detail instruction), he may set up an index for it. Enter the
Class Name of Index 3. In this index, he will set reserve bandwidth for 1 VPN tunnel.
And click
Advanced
button on the right.
8.
Click edit to open a new window. First, check the ACT box. Then click
SrcEdit t
o set a
worker’s subnet address. Click
DestEdit
to set headquarter’s subnet address. Leave
other fields and click OK.
Page 180 / 202
Vigor2800 Series User’s Guide
174
4.4 LAN – Created by Using NAT
An example of default setting and the corresponding deployment are shown below. The
default Vigor router private IP address/Subnet Mask is
192.168.1.1/255.255.255.0. The
built-in DHCP server is enabled so it assigns every local NATed host an IP address of
You can just set the settings wrapped inside the red rectangles to fit the request of NAT
usage.
19216811.live