DrayTek Vigor-2110 Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

DrayTek

Vigor-2110

Page 41 / 275 Scroll up to view Page 36 - 40

Vigor2110 Series User’s Guide

IP Address

Type in secondary IP address for connecting to a subnet.

(Default: 192.168.2.1/ 24)

Subnet Mask

An address code that determines the size of the network.

(Default: 255.255.255.0/ 24)

DHCP Server

You can configure the router to serve as a DHCP server for the 2nd

subnet.

Start IP Address:

Enter a value of the IP address pool for the DHCP

server to start with when issuing IP addresses. If the 2nd IP address

of your router is 220.135.240.1, the starting IP address must be

220.135.240.2 or greater, but smaller than 220.135.240.254.

IP Pool Counts:

Enter the number of IP addresses in the pool. The

maximum is 10. For example, if you type 3 and the 2nd IP address of

your router is 220.135.240.1, the range of IP address by the DHCP

server will be from 220.135.240.2 to 220.135.240.11.

MAC Address:

Enter the MAC Address of the host one by one and

click

Add

to create a list of hosts to be assigned, deleted or edited IP

address from above pool. Set a list of MAC Address for 2

DHCP

server will help router to assign the correct IP address of the correct

subnet to the correct host. So those hosts in 2

subnet won’t get an

IP address belonging to 1

subnet.

RIP Protocol Control

Disable

deactivates the RIP protocol. It will lead to a stoppage of the

exchange of routing information between routers. (Default)

1st Subnet -

Select the router to change the RIP information of the

1st subnet with neighboring routers.

2nd Subnet -

Select the router to change the RIP information of the

2nd subnet with neighboring routers.

Page 42 / 275

Vigor2110 Series User’s Guide

DHCP Server

Configuration

DHCP stands for Dynamic Host Configuration Protocol. The

router by factory default acts a DHCP server for your network so

it automatically dispatch related IP settings to any local user

configured as a DHCP client. It is highly recommended that you

leave the router enabled as a DHCP server if you do not have a

DHCP server for your network.

If you want to use another DHCP server in the network other than

the Vigor Router’s, you can let Relay Agent help you to redirect the

DHCP request to the specified location.

Enable Server -

Let the router assign IP address to every host in the

LAN.

Disable Server –

Let you manually assign IP address to every host

in the LAN.

Relay Agent – (1

subnet/2

subnet)

Specify which subnet that

DHCP server is located the relay agent should redirect the DHCP

request to.

Start IP Address -

Enter a value of the IP address pool for the

DHCP server to start with when issuing IP addresses. If the 1st IP

address of your router is 192.168.1.1, the starting IP address must be

192.168.1.2 or greater, but smaller than 192.168.1.254.

IP Pool Counts -

Enter the maximum number of PCs that you want

the DHCP server to assign IP addresses to. The default is 50 and the

maximum is 253.

Gateway IP Address -

Enter a value of the gateway IP address for

the DHCP server. The value is usually as same as the 1st IP address

of the router, which means the router is the default gateway.

DHCP Server IP Address for Relay Agent -

Set the IP address of

the DHCP server you are going to use so the Relay Agent can help to

forward the DHCP request to the DHCP server.

DNS Server

Configuration

DNS stands for Domain Name System. Every Internet host must

have a unique IP address, also they may have a human-friendly,

easy to remember name such as www.yahoo.com. The DNS

server converts the user-friendly name into its equivalent IP

address

Force DNS manual setting -

Force Vigor router to use DNS servers

in this page instead of DNS servers given by the Internet Access

server (PPPoE, PPTP, L2TP or DHCP server).

Primary IP Address -

You must specify a DNS server IP address

here because your ISP should provide you with usually more than

one DNS Server. If your ISP does not provide it, the router will

automatically apply default DNS Server IP address: 194.109.6.66 to

this field.

Secondary IP Address -

You can specify secondary DNS server IP

address here because your ISP often provides you more than one

DNS Server. If your ISP does not provide it, the router will

automatically apply default secondary DNS Server IP address:

194.98.0.1 to this field.

The default DNS Server IP address can be found via Online Status:

Page 43 / 275

Vigor2110 Series User’s Guide

If both the Primary IP and Secondary IP Address fields are left empty,

the router will assign its own IP address to local users as a DNS

proxy server and maintain a DNS cache.

If the IP address of a domain name is already in the DNS cache, the

router will resolve the domain name immediately. Otherwise, the

router forwards the DNS query packet to the external DNS server by

establishing a WAN (e.g. DSL/Cable) connection.

There are two common scenarios of LAN settings that stated in Chapter 4. For the

configuration examples, please refer to that chapter to get more information for your necessity.

3.3 NAT

Usually, the router serves as an NAT (Network Address Translation) router. NAT is a

mechanism that one or more private IP addresses can be mapped into a single public one.

Public IP address is usually assigned by your ISP, for which you may get charged. Private IP

addresses are recognized only among internal hosts.

When the outgoing packets destined to some public server on the Internet reach the NAT

router, the router will change its source address into the public IP address of the router, select

the available public port, and then forward it. At the same time, the router shall list an entry in

a table to memorize this address/port-mapping relationship. When the public server response,

the incoming traffic, of course, is destined to the router’s public IP address and the router will

do the inversion based on its table. Therefore, the internal host can communicate with external

host smoothly.

The benefit of the NAT includes:

Save cost on applying public IP address and apply efficient usage of IP address.

NAT allows the internal IP addresses of local hosts to be translated into one public IP

address, thus you can have only one IP address on behalf of the entire internal hosts.

Enhance security of the internal network by obscuring the IP address.

There are

many attacks aiming victims based on the IP address. Since the attacker cannot be aware

of any private IP addresses, the NAT function can protect the internal network.

On NAT page, you will see the private IP address defined in RFC-1918. Usually we use the

192.168.1.0/24 subnet for the router. As stated before, the NAT facility can map one or

more IP addresses and/or service ports into different specified services. In other words, the

NAT function can be achieved by using port mapping methods.

Below shows the menu items for NAT.

3.3.1 Port Redirection

Port Redirection

usually set up for server related service inside the local network (LAN),

such as web servers, FTP servers, E-mail servers etc. Most of the case, you need a public IP

address for each server and this public IP address/domain name are recognized by all users.

Since the server is actually located inside the LAN, the network well protected by NAT of the

router, and identified by its private IP address/port, the goal of Port Redirection function is to

forward all access request with public IP address from external users to the mapping private IP

address/port of the server.

Page 44 / 275

Vigor2110 Series User’s Guide

The port redirection can only apply to incoming traffic.

To use this function, please go to

NAT

page and choose

Port

Redirection

web page. The

Port Redirection Table

provides 20 port-mapping entries for the internal hosts.

Press any number under Index to access into next page for configuring port redirection.

Page 45 / 275

Vigor2110 Series User’s Guide

Enable

Check this box to enable such port redirection setting.

Mode

Two options (Single and Range) are provided here for you to choose.

To set a range for the specific service, select

Range

. In Range mode,

if the public port (start port and end port) and the starting IP of

private IP had been entered, the system will calculate and display the

ending IP of private IP automatically.

Service Name

Enter the description of the specific network service.

Protocol

Select the transport layer protocol (TCP or UDP).

WAN IP

Select the WAN IP used for port redirection. There are eight WAN

IP alias that can be selected and used for port redirection. The

default setting is

All

which means all the incoming data from any

port will be redirected to specified range of IP address and port.

Public Port

Specify which port can be redirected to the specified

Private IP and

Port

of the internal host. If you choose

Range

as the port redirection

mode, you will see two boxes on this field. Simply type the required

number on the first box. The second one will be assigned

automatically later.

Private IP

Specify the private IP address of the internal host providing the

service. If you choose

Range

as the port redirection mode, you will

see two boxes on this field. Type a complete IP address in the first

box (as the starting point) and the fourth digits in the second box (as

the end point).

Private Port

Specify the private port number of the service offered by the internal

host.

Note that the router has its own built-in services (servers) such as Telnet, HTTP and FTP etc.

Since the common port numbers of these services (servers) are all the same, you may need to

reset the router in order to avoid confliction.

3.3.2 DMZ Host

As mentioned above,

Port Redirection

can redirect incoming TCP/UDP or other traffic on

particular ports to the specific private IP address/port of host in the LAN. However, other IP

protocols, for example Protocols 50 (ESP) and 51 (AH), do not travel on a fixed port. Vigor

router provides a facility

DMZ Host

that maps ALL unsolicited data on any protocol to a

Rate

Popular DrayTek Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share