Page 11 / 45
Scroll up to view Page 6 - 10
DVG-N5402SP
User’s Manual
SETUP
D-Link Systems, Inc.
8
SETUP
→
Wireless Setup
→
Wireless Security (WEP)
WEP Key Length:
Select 64-bit or 128-bit data encryption.
Default Tx Key:
You can select one of the keys as active key at a time.
WEP Key Format:
Select the preferred WEP Key Format according to which WEP encryption you choose.
When WEP 64bits is enabled, you can select ASCII (5 characters) and Hex (10 characters). When WEP
128bits is enabled, you can select ASCII (13 characters) and Hex (26 characters).
WEP Key 1
–
4:
You can manually enter key value from Key1 to Key4. Type a character sting and apply
changes.
For a 64-bit WEP key - Enter 5 characters (ASCII sting) or 10 hexadecimal characters (
“
0-9
”
,
“
A-F
”
).
For a 128-bit WEP key - Enter 13 characters (ASCII sting) or 26 hexadecimal characters (
“
0-9
”
,
“
A-F
”
).
Page 12 / 45
DVG-N5402SP
User’s Manual
SETUP
D-Link Systems, Inc.
9
WPA Authentication Mode
The wireless network can use WPA Authentication to verify whether a wireless device is allowed to access
your Access Point or not. You can choose to use Enterprise (RADIUS) method or Personal (Pre-Shared
Key). The encryption mechanism used for RADIUS and WPA-PSK is the same. The difference between the
two is that WPA-PSK uses a specific characters sting like password instead of a user-authentication.
SETUP
→
Wireless Setup
→
Wireless Security (WPA-PSK)
If
WPA Security Mode
is set to
WPA
(
WPA only
,
WPA2 only
, or
WPA/WP2 Mixed
), you can set
WPA
Mode
to
WPA-Personal
or
WPA-Enterprise
, select the security mode according to your wireless network.
Encryption Mode:
Encryption mode
is used for the configuration of WPA or WPA2 Mixed.
TKIP -
TKIP is the security protocol used in WPA. The length of TKIP encryption is longer than WEP
encryption that increases the complexity of decoding for crackers.
AES -
The most powerful encryption algorithm that is commonly used in WPA.
Group Key Update Interval:
Set the update interval of the group key.
Pre-Shared Key:
Enter a key of 8-64 characters long in the Pre-Shared Key filed. Make sure this key is
exactly the same on all other wireless stations. By default, the Pre-Shared Key will be the serial number
located below your device. Use that to access your wireless network.
Page 13 / 45
DVG-N5402SP
User’s Manual
SETUP
D-Link Systems, Inc.
10
SETUP
→
Wireless Settings
→
Wireless Security (WPA-Enterprise)
If
WPA Security Mode
is set to
WPA
(
WPA only
,
WPA2 only
, or
WPA2 Mixed
), you can set
WPA Mode
to
WPA-Enterprise
(
WPA- Enterprise
,
WPA2- Enterprise
,
WPA2 Mixed- Enterprise
), select the security
mode according to your wireless network.
WPA Mode:
Select
WPA-Enterprise
.
WPA Cipher Suite:
WPA Cipher Suite is used for the configuration of WPA or WPA2 Mixed.
TKIP -
TKIP is the security protocol used in WPA. The length of TKIP encryption is longer than WEP
encryption that increases the complexity of decoding for crackers.
AES -
The most powerful encryption algorithm that is commonly used in WPA.
RADIUS Server:
RADIUS server IP Address -
Enter the IP address of the authentication RADIUS server.
RADIUS server Port -
Enter the port number of the authentication RADIUS server. Keep the default
value: 2801 unless the server required change to another number.
RADIUS server Shared Secret -
Enter the password such as a security Key.
Page 14 / 45
DVG-N5402SP
User’s Manual
SETUP
D-Link Systems, Inc.
11
3-1-1-3 WPS
SETUP
→
Wireless Setup
→
WPS
Wireless SSID:
Select the VAP (Virtual Access Point) of which the WPS function is enabled.
Note:
There is only one VAP of which the WPS function is enabled each time. If the WPS function of the
VAP has been enabled, the WPS function would be disabled before you enable the WPS function of
another VAP.
Enable:
Enable or disable the WPS function. The WPS function of the VoIP Router only supports the
following three authentication methods:
WPA2-PSK
,
WPA2-PSK
, or
WPA2-Mixed
. If the page is in gray,
you need to enable
WPA2-PSK
,
WPA2-PSK
, or
WPA2-Mixed
.
PBC Button:
Click the
PBC
button to trigger WPS negotiation session through PBC.
Input Station PIN:
Enter the PIN code (Personal Identification Number) of the station.
WPS Session Status:
It shows the. There are four WPS negotiation status:
INPROCESS
,
ERROR
,
SUCCESS
, or
OVERLAP
.
Page 15 / 45
DVG-N5402SP
User’s Manual
SETUP
D-Link Systems, Inc.
12
3-1-2 LAN Setup
SETUP
→
LAN Setup
Router IP Address:
Enter the LAN IP address of the VoIP Router. It is also the default gateway for DHCP
clients.
Subnet Mask:
Enter the subnet mask for DHCP clients.
19216811.live