D-Link DVG-N5402SP Router Manual PDF (Setup & Configuration Guide)

Page 6 / 45 Scroll up to view Page 1 - 5

DVG-N5402SP

User’s Manual

Hardware Description

D-Link Systems, Inc.

3

Rear Panel

1.

Antenna:

Connect to a

wireless network.

2.

LINE:

Connect to the

telephone line on the wall jack

through a telephone cable.

3.

PHONE2/PHONE1:

Connect to your phones through

a standard telephone cable.

4.

USB:

USB host 2.0 port,

for connecting to another USB

device to supply some

value-added application.

5.

LAN4/LAN3/LAN2/LAN1:

RJ-45 port, for connecting to the

Ethernet port of a PC or the

Ethernet devices through an

Ethernet cable.

6.

WAN:

Connect to your

ONT through an Ethernet cable.

7.

POWER:

Power adapter, for connecting to the power adapter of 12V, 2A.

8.

RESET:

Restore to factory defaults. To restore factory defaults, keep the VoIP Router powered on, push a

paper clip into the hole to press the button for over 5 seconds and then release.

9.

WPS:

Button to enable or disable WPS.

10.

ON/OFF:

Power switch, power on or power off the VoIP Router.

WARNING:

DO NOT

(1) connect the phone ports to each other (FXS to FXS) or (2) connect any

phone port directly to a PSTN line (FXS to PSTN) or to an internal PBX line (FXS to PBX extension).

(3) Stacking is forbidden. Doing so may damage your VoIP Router.

Use the Reset Button to restore factory default settings:

1.

Power on.

2.

Press and hold the Reset button for over 5 seconds.

3.

Release the Reset button. Factory settings are restored.

Page 7 / 45

DVG-N5402SP

User’s Manual

SETUP

D-Link Systems, Inc.

4

2. Getting Started

To access the Web-based configuration utility, open a Web browser such as IE (Internet Explorer) and enter the

IP address of the DVG-N5402SP from LAN port.

The default username and password of user account: admin/password .

Open your Web browser and enter

http://192.168.0.1

into the URL address

bar. Click Enter.

Click

Login

to enter Web site.

Page 8 / 45

DVG-N5402SP

User’s Manual

SETUP

D-Link Systems, Inc.

5

3. VoIP Router Web Configuration (continued)

3-1 SETUP

3-1-1 Wireless Setup

This section instructs you how to setup your wireless network on the VoIP Router device.

Setup Hint:

1.

Every device in the same wireless network must use the same SSID.

2.

To avoid wireless network overlap, a specific and different channel is needed.

3.

Make sure security used by every device in the same wireless network is compatible with the wireless

AP.

3-1-1-1 Wireless Basic

SETUP

→

Wireless Setup

→

Wireless Basic

Enable Wireless LAN Interface:

Enable wireless basic settings on LAN interface.

Page 9 / 45

DVG-N5402SP

User’s Manual

SETUP

D-Link Systems, Inc.

6

Wireless Network Name (SSID):

SSID is the name of your wireless network. All wireless-equipped

devices share the same SSID to communicate with each other. It must be unique to identify separated

wireless network. For security, you should change the default SSID to a special ID. By default the SSID will

be name “DVG

-N5402SP-

XXXXXX” and “XXXXXX” will be the last 6 numbers of your

WAN connection

“TR069”

MAC Address.

Visibility Status:

Select the visibility status.

Visible

indicates that the device broadcasts the SSID.

Invisible

indicates that the device does not broadcast the SSID.

Country:

Select the country where you are located from the drop-down menu.

802.11 Mode:

The VoIP Router can operate in 2.4GHz ISM band with different speed of wireless

connection, Select the wireless band of your network.

802.11b only -

Allow all 802.11B compliant wireless devices to associate with the wireless AP.

802.11g only -

Allow all 802.11G compliant wireless devices to associate with the wireless AP.

802.11n only -

Allow all 802.11N compliant wireless devices to associate with the wireless AP.

Mixed 802.11b/g

–

Allow a mix of both 802.11B and 802.11G compliant wireless devices to associate

with the wireless AP.

Mixed 802.11n/g

- Allow a mix of both 802.11N and 802.11G compliant wireless devices to associate

with the wireless AP.

Mixed 802.11b/g/n

- Allow a mix of 802.11B, 802.11G, and 802.11N compliant wireless devices to

associate with the wireless AP.

Bandwidth:

Select the bandwidth from the drop-down list. You can select

20M, 40M Plus,

or

40M Minus

.

Wireless Channel:

Select a clear and appropriate channel for your wireless network. A device on your

wireless network must use a specific channel to transmit and receive data. If wireless network has overlap,

change a different channel number.

User Isolation

: The isolation among all the stations that are connected with the same VAP (Virtual Access

Point). You can select

Off

or

On

.

Page 10 / 45

DVG-N5402SP

User’s Manual

SETUP

D-Link Systems, Inc.

7

3-1-1-2 Wireless Security

This section introduces you different ways of wireless security you can set up. It is important to enable

secure algorithm to protect your data from eavesdropping by unauthorized wireless users.

SETUP

→

Wireless Setup

→

Wireless Security

Wireless Security Mode:

Select the encryption/authentication type:

None

,

WEP

,

WPA only

,

WPA2 only

,

or

WPA/WP2 Mixed

.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share