Page 51 / 83
Scroll up to view Page 46 - 50
49
2.
Define a name such as ‘voip’ for this new connection.
Figure 4.2: Edit the name for the connection
3.
After pressing OK button, the next window appear, and then choose
COM1/2
Port
, which you are going to use.
Figure 4.3: Pick up the right interface to use
Page 52 / 83
50
4.
Configure the COM Port Properties as following:
±
Bits per second: 9600
±
Flow control: None
Figure 4.4: Configure the right Bps and control
5.
Press ‘OK’ button, and then start to configure Gateway.
Page 53 / 83
51
4.2 Command List
4.2.1 [help]
Type
help
or
man
or
?
to list all the available command.
usr/config$ ?
help
help/man/? [command]
quit
quit/exit/close
debug
show debug message
reboot
reboot local machine
flash
clean configuration from flash rom
commit
commit flash rom data
ifaddr
internet address manipulation
time
show current time
ping
test that a remote host is reachable
sysconf
System information manipulation
sip
SIP information manipulation
security
Security information manipulation
line
Line information manipulation
route
Routing information manipulation
prefix
Prefix drop/insert information manipulation
pbook
Phone book information manipulation
voice
Voice information manipulation
tone
Setup of disconnect tone and remote ring back tone
fxopwd
Setup of FXO password
record
Record voice for greeting and ask pin code
tos
IP Packet ToS (Type of Service)values
pt
DSP payload type configuration and information
rom
ROM file update
passwd
Password setting information and configuration
usage: help [command]
usr/config$
Page 54 / 83
52
4.2.2 [quit]
Type
quit
will quit the configuration mode. And turn back to login prompt.
usr/config$ quit
Disconnecting...
login:
Note:
It is recommended that type the “
quit
” command before you leave the console. If
so, the unit will ask password again when next user connects to console port.
4.2.3 [debug]
Open debug message will show up specific information while DVG-3004S is in
operation. After executing the debug command, it should execute command
debug -open
as well. One example is demonstrated below.
usr/config$ debug -add sip vp
usr/config$ debug -open
Parameters Usage:
-status
Display the enabled debug flags.
-add
Add debug flag.
-- sip : sip related information
-- vp : voice related information
-delete
Remove specified debug flag.
-open
Start to show debug messages.
-close
Stop showing debug messages.
4.2.4 [reboot]
After
commit
command, type
reboot
to reload DVG-3004S in new configuration. The
procedure is as below:
usr/config$ reboot
Attached TCP/IP interface to cpm unit 0
Attaching interface lo0...done
AC4804[0] is OK
AC4804[1] is OK
AC4804[2] is OK
Successful
Initialize OSS libraries...OK!
Page 55 / 83
53
open stack successful
cmInitialize succeed!
GK mode selected.
login:
4.2.5 [flash]
This command will clean the configuration stored in the flash rom and reboot
DVG-3004S in factory default setting.
Parameter Usage:
-clean
clean all the user-defined value, and reboot DVG-3004S in
factory default mode.
Note: It is recommended that use “flash –clean” after application firmware id
upgraded.
Warning
:
Once users execute
flash –clean,
all the configurations of
DVG-3004S will be cleaned. This can only be executed by user who log in
with
root
4.2.6 [commit]
Save changes after configuring the DVG-3004S.
-------------------------------------------------------------------------------------------------
usr/config$ commit
This may take a few seconds, please wait
....
Commit to flash memory ok!
usr/config$
Note: Users should use
commit
to save modified value, or they will not be
activated after system reboot
.
4.2.7 [ifaddr]
Configure and display DVG-3004S network information.
19216811.live