Page 41 / 84
Scroll up to view Page 36 - 40
41
D-Link DSL-500B User Manual
Web Configuration
Statistics - ADSL
Select
Device Info >
Statistics
>
ADSL
. The
Statistics - ADSL
page will appear. This page displays the Router’s ADSL statistics.
Click
Reset Statistics
to refresh these statistics.
Click
ADSL BER Test
to access the ADSL Bit Error Rate Test
window.
ADSL BER Test
The ADSL Bit Error Rate (BER) test determines the quality of
the ADSL connection. The test is done by transferring idle cells
containing a known pattern and comparing the received data with
this known pattern to check for any errors.
Click
ADSL BER Test
to perform a bit error rate (BER) test on the
DSL line.
The tested time (in seconds) can be 1, 5, 10, 20, 60, 120, 180, 240,
300, or 360. Select a time and click
Start
.
The following pages will appear.
Page 42 / 84
42
D-Link DSL-500B User Manual
Web Configuration
Note:
If the BER reaches e-5, you cannot access the Internet.
Route Table Information
Select
Device Info > Route
. The
Device-Route
page will appear if
the system is in the default configuration.
ARP Table Information
Select
Device Info >
ARP.
This page displays information on the
Address Resolution Protocol (ARP).
DHCP Information
Select
Device Info >
DHCP
. This page displays the DHCP lease
information.
Page 43 / 84
43
D-Link DSL-500B User Manual
Web Configuration
WAN Configuration
Select
Advanced Setup > WAN.
This page allows you to modify
and configure the WAN interface.
Note:
After a PVC is deleted or modified, the system must be
rebooted. Otherwise, the modification does not take effect.
Click
Add
,
Edit
, or
Remove
to configure your WAN interface.
Click
Save/Reboot
to save the modification, and reboot the
modem to make the modification effective.
If you are setting up the WAN interface for the first time, click
Add
and the
ATM PVC Configuration
page will appear.
Advanced Setup
This chapter includes advanced features used for network management and security as well as administrative tools
to manage the Router, view status and other information which is used to examine the performance and for
troubleshooting.
Page 44 / 84
44
D-Link DSL-500B User Manual
Web Configuration
In this page, you can modify VPI/VCI, service categories, and QoS.
VPI:
Virtual path between two points in an ATM network. Its valid
value range is from 0 to 255.
VCI:
Virtual channel between two points in an ATM network. Its
valid value range is from 32 to 65535 (1 to 31 are reserved for
known protocols).
Service Category:
UBR Without PCR/UBR With PCR/CBR/Non
Realtime VBR/Realtime VBR.
Enable Quality Of Service:
Enable or disable QoS.
After the modifications, click
Next
and the
Connection Type
page
will appear.
This page allows you to select the appropriate connection type.
The choices include
PPP over ATM (PPPoA), PPP over Ethernet
(PPPoE), MAC Encapsulation Routing (MER), IP over ATM
(IPoA),
and
Bridging
(default).
Select the desired
Encapsulation Mode
from the drop-down box
and then click
Next
to continue.
Refer to the
Quick Setup
section for more information on the five
connection types available in the Router.
Page 45 / 84
45
D-Link DSL-500B User Manual
Web Configuration
LAN Configuration
Select
Advanced Setup > LAN
and the
Local Area Network
(LAN) Setup
page will appear. Here you can modify and configure
the IP Address, DHCP Server and enable IGMP Snooping.
Note:
The most convenient way to manage your network is to use
the default settings along with the DHCP services. In order to use
the Router for DHCP settings, the IP address used for DHCP must
be compatible with the IP address of the Router. The IP addresses
available in the DHCP IP address pool will change automatically if
you change the IP address of the Router.
When you are finished, click either
Save
to save the LAN configu
-
ration or
Save/Reboot
to save the data and reboot the Router.
19216811.live