Page 91 / 154
Scroll up to view Page 86 - 90
87
D-Link DSL-4320L User Manual
Section 4 - Configuration
PPPoE
Choose
Share with IPv4
to re-use your IPv4 PPPoE username and
password, or
Create a new session
.
If you selected
Create a new session
above, enter the PPPoE
username provided by your ISP here.
If you selected
Create a new session
above, enter the PPPoE
password provided by your ISP here.
Select
Static IP
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select
Dynamic IP
.
Enter the IP address provided by your ISP (Static IP only).
Maximum Transmission Unit - you may need to change the MTU for
optimal performance with your ISP.
Select either
Obtain DNS server address automatically
or
Use the
following DNS address
.
If you selected
Use the following DNS address
above, enter the
primary DNS server address.
If you selected
Use the following DNS address
above, enter the
secondary DNS server address.
Enable or disable prefix delegation services.
PPPoE Session:
Username:
Password:
Address Mode:
IP Address:
MTU:
DNS Type:
Primary DNS
Server:
Secondary DNS
Server:
Enable DHCP-
PD:
Select
PPPoE
if your Internet connection requires you to enter a username and password. This information is provided by your Internet Service
Provider (ISP).
Page 92 / 154
88
D-Link DSL-4320L User Manual
Section 4 - Configuration
Enter the LAN (local) IPv6 address for the router.
Displays the router’s LAN link-local address.
Enable or disable the Automatic IPv6 Address Assignment feature.
Enable or disable DHCP-PD for other IPv6 routers connected to the
LAN interface.
Note:
This feature requires a smaller subnet prefix than /64 (i.e. allowing
for a larger address allocation), such as /63. Contact your ISP for more
information.
Select
Stateful (DHCPv6)
,
SLAAC + RDNSS
or
SLAAC + Stateless
DHCPv6
.
Enter the IPv6 address lifetime (in minutes).
Click
Save
when you are done.
LAN IPv6 Address:
LAN IPv6 Link-
Local Address:
Enable Automatic
IPv6 Address
Assignment:
Enable Automatic
DHCP-PD in LAN:
Autoconfiguration
Type:
Router
Advertisement
Lifetime:
Page 93 / 154
89
D-Link DSL-4320L User Manual
Section 4 - Configuration
IPv6 in IPv4 Tunnel
Enter the IPv4 remote address you will use.
Enter the IPv6 remote address you will use.
Enter the IPv4 local address you will use.
Enter the IPv6 local address you will use.
Enter the subnet prefix length supplied by your ISP.
Select either
Obtain DNS server address automatically
or
Use the
following DNS address
.
If you selected
Use the following DNS address
above, enter the
primary DNS server address.
If you selected
Use the following DNS address
above, enter the
secondary DNS server address.
Enable or disable prefix delegation services.
If you disabled DHCP-PD, enter the LAN (local) IPv6 address for the
router.
Remote IPv4
Address:
Remote IPv6
Address:
Local IPv4
Address:
Local IPv6
Address:
Subnet Prefix
Length:
DNS Type:
Primary DNS
Server:
Secondary DNS
Server:
Enable DHCP-
PD:
LAN IPv6
Address:
The user can configure the IPv6 connection to run in IPv4 Tunnel mode. IPv6 over IPv4 tunneling encapsulates IPv6 packets in IPv4 packets so
that IPv6 packets can be sent over an IPv4 infrastructure.
Page 94 / 154
90
D-Link DSL-4320L User Manual
Section 4 - Configuration
Displays the router’s LAN link-local address.
Enable or disable the Automatic IPv6 Address Assignment feature.
Enable or disable automatic DHCP-PD services.
Select
Stateful (DHCPv6)
,
SLAAC + RDNSS
or
SLAAC + Stateless
DHCPv6
.
Enter the IPv6 address lifetime (in minutes).
Click
Save
when you are done.
LAN IPv6 Link-
Local Address:
Enable
Automatic
IPv6 Address
Assignment:
Enable
Automatic
DHCP-PD in
LAN:
Auto
Configuration
Type:
Router
Advertisement
Lifetime:
Page 95 / 154
91
D-Link DSL-4320L User Manual
Section 4 - Configuration
6 to 4
Displays the 6 to 4 address.
Enter the 6 to 4 relay supplied by your ISP.
Enter the primary DNS server address.
Enter the secondary DNS server address.
Enter the LAN (local) IPv6 address for the router.
Displays the router’s LAN link-local address.
Check to enable the Automatic IPv6 Address Assignment feature.
Select
Stateful (DHCPv6)
,
SLAAC + RDNSS
or
SLAAC + Stateless
DHCPv6
.
Enter the IPv6 address lifetime (in minutes).
Click
Save
when you are done.
6 to 4 Address:
6 to 4 Relay:
Primary DNS
Server:
Secondary DNS
Server:
LAN IPv6 Address:
LAN IPv6 Link-
Local Address:
Enable Automatic
IPv6 Address
Assignment:
Autoconfiguration
Type:
Router
Advertisement
Lifetime:
In this section the user can configure the IPv6 6 to 4 connection settings. 6to4 is an IPv6 address assignment and automatic tunneling
technology that is used to provide unicast IPv6 connectivity between IPv6 sites and hosts across the IPv4 Internet.
19216811.live