Page 71 / 154
Scroll up to view Page 66 - 70
67
D-Link DSL-4320L User Manual
Section 4 - Configuration
Settings
Wizard
Internet
In the Settings menu on the bar on the top of the page, click
Wizard
to open the setup wizard. This is the same wizard that appears when you start
the router for the first time. Refer to
Setup Wizard
on page 14 for more information.
In the Settings menu on the bar on the top of the page, click
Internet
to see the
Internet configuration options. Click
Advanced Settings...
to expand the list and
see all of the options.
You will see the settings for your
IPv4
connection.
To configure the advanced DSL settings, click the
DSL
link. Refer to
DSL on page 78
.
To configure the ATM settings, click the
ATM
link. Refer to
ATM on page 79
.
To configure the PTM settings, click the
PTM
link. Refer to
PTM on page 80
.
To configure an IPv6 connection, click the
IPv6
link. Refer to
IPv6 on page 81
.
Page 72 / 154
68
D-Link DSL-4320L User Manual
Section 4 - Configuration
For
Dynamic IP (DHCP)
refer to
Dynamic IP (DCHP) on page
69
.
For
Static IP
refer to
Static IP on page 70.
For
PPPoE
refer to
PPPoE on page 71.
For
PPPoA
refer to
PPPoA on page 72.
For
PPTP
refer to
PPTP on page 73.
For
L2TP
refer to
L2TP on page 75.
For
Bridge
refer to
Bridge on page 77.
Select whether the device should act as an
xDSL Router
or a
Residential Gateway
.
Use the default setting unless otherwise instructed by your ISP.
If you selected
Residential Gateway
, sselect the Ethernet port that
will connect to the WAN. Use this setting if you do not intend to use
the built-in DSL modem.
Enable or disable tagged VLAN.
Enter the VLAN ID.
Enter the VLAN Priority from the default 0 (lowest) to 7 (highest).
Choose your Internet connection type from the drop-down menu.
You will be presented with the appropriate options for your
connection type.
WAN Access
Type:
PVC:
Ether WAN Port:
Enable Tagged
Vlan:
VLAN ID:
VLAN Priority:
My Internet
Connection Is:
In the Settings menu on the bar on the top of the page, click
Internet
to see the
Internet configuration options. Click
Advanced Settings...
to expand the list and
see all of the options.
Page 73 / 154
69
D-Link DSL-4320L User Manual
Section 4 - Configuration
The host name is optional but may be required by some ISPs. Leave
it blank if you are not sure.
Enter the primary DNS server IP address assigned by your ISP. This
address is usually obtained automatically from your ISP.
Enter the secondary DNS server IP address assigned by your ISP. This
address is usually obtained automatically from your ISP.
Maximum Transmission Unit - you may need to change the MTU for
optimal performance with your ISP.
The default MAC address is set to the Internet port’s physical interface
MAC address on the router. You can use the drop-down menu to
replace the Internet port’s MAC address with the MAC address of a
connected client.
Click
Save
when you are done.
Host Name:
Primary DNS
Server:
Secondary DNS
Server:
MTU:
MAC Address
Clone:
Dynamic IP (DCHP)
Select
Dynamic IP (DHCP)
to obtain IP address information automatically from your Internet Service Provider (ISP). Select this option if your ISP
does not give you an IP address to use.
IPv4
Page 74 / 154
70
D-Link DSL-4320L User Manual
Section 4 - Configuration
Enter the IP address provided by your ISP.
Enter the subnet mask provided by your ISP.
Enter the default gateway address provided by your ISP.
Enter the primary DNS server IP address assigned by your ISP.
Enter the secondary DNS server IP address assigned by your ISP.
Maximum Transmission Unit - you may need to change the MTU for
optimal performance with your ISP.
The default MAC address is set to the Internet port’s physical interface
MAC address on the router. You can use drop-down menu to replace
the Internet port’s MAC address with the MAC address of a connected
client.
Click
Save
when you are done.
IP Address:
Subnet Mask:
Default
Gateway:
Primary DNS
Server:
Secondary DNS
Server:
MTU:
MAC Address
Clone:
Static IP
Select
Static IP
if your IP information is provided by your Internet Service Provider (ISP).
Page 75 / 154
71
D-Link DSL-4320L User Manual
Section 4 - Configuration
Enter the username provided by your ISP.
Enter the password provided by your ISP.
Select either
Always-on
,
On-Demand
, or
Manual
.
Select
Static IP
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select
Dynamic IP
.
Enter the IP address provided by your ISP (Static IP only).
Enter the ISP service name (optional).
Enter the primary DNS server IP address assigned by your ISP.
Enter the secondary DNS server IP address assigned by your ISP.
Maximum Transmission Unit - you may need to change the MTU for
optimal performance with your ISP.
Click
Save
when you are done.
Username:
Password:
Reconnect
Mode:
Address Mode:
IP Address:
Service Name:
Primary DNS
Server:
Secondary DNS
Server:
MTU:
Select
PPPoE
if your Internet connection requires you to enter a PPPoE username and password. This information is provided by your Internet
Service Provider (ISP).
PPPoE
19216811.live