Page 26 / 103
Scroll up to view Page 21 - 25
DSL-2750E User Manual
23
The above figure shows the when the Security Mode is set as
Auto (WPA or
WPA2)
. The following table describes the parameters in this page.
Field
Description
WPA
Encryption
You can select WPA encryption to be
AES
or
TKIP+AES
.
WPA Mode
Select
Auto (WPA or WPA2)-PSK
, enter the
pre-shared key in the
Pre-Shared Key
field.
Select
Auto
(WPA
or
WPA2)-Enterprise
(RADIUS)
, enter the port, IP address, and password of
the Radius server. You need to enter the username
and password provided by the Radius server when the
wireless client connects the modem.
Group Key
When WPA encryption is applied, messages sent are
Page 27 / 103
DSL-2750E User Manual
24
Field
Description
Update Interval
encrypted with a password. For higher security, WPA
password is updated periodically. This value is the
update interval of the WPA password.
Click
Apply
to save the settings.
3.2.4
Local Network
You can configure the LAN IP address according to the actual application. The
preset IP address is
192.168.1.1. You can use the default settings and DHCP
service to manage the IP settings for the private network. The IP address of the
device is the base address used for DHCP. To use the device for DHCP on your
LAN, the IP address pool used for DHCP must be compatible with the IP address
of the device. The IP address available in the DHCP IP address pool changes
automatically if you change the IP address of the device.
You can also enable the secondary LAN IP address. The two LAN IP addresses
must be in different networks.
Choose
Setup
>
Local Network
. The
Local Network
page shown in the
following figure appears.
Page 28 / 103
DSL-2750E User Manual
25
The following table describes the parameters in this page
Field
Description
Router IP Address
Enter the IP address of LAN interface. It is
recommended to use an address from a block that is
reserved for private use. This address block is
192.168.1.1
-
192.168.255.254
.
Subnet Mask
Enter the subnet mask of LAN interface. The range of
subnet mask is from
255.255.0.0
-
255.255.255.254
.
Domin Name
Enter the domain name if you know. If you leave this
blank, the domain name obtained by DHCP from the
ISP is used. You must enter host name (system
name) on each individual PC. The domain name can
be assigned from the router through the DHCP
Page 29 / 103
DSL-2750E User Manual
26
Field
Description
server.
Configure the
second IP Address
and Subnet Mask
for LAN
Select it to enable the secondary LAN IP address.
The two LAN IP addresses must be in the different
network.
Enable DHCP
Server
Enable the router to assign IP addresses, IP default
gateway and DNS Servers to the host in Windows95,
Windows NT and other operation systems that
support the DHCP client.
DHCP IP Address
Range
It specifies the first IP address in the IP address pool.
The router assigns IP address that base on the IP
pool range to the host.
DHCP Lease Time
The lease time determines the period that the host
retains the assigned IP addresses before the IP
addresses change.
Click
Apply
to make the settings take effect.
The
DHCP RESERVATIONS LIST
shown in the following figure appears.
Click
Add
to add DHCP (optional). The page shown in the following figure
appears.
Page 30 / 103
DSL-2750E User Manual
27
Select
Enable
to reserve the IP address for the designated PC with the
configured MAC address. The
Computer Name
helps you to recognize the PC
with the MAC address, for example, Father’s Laptop. Click
Apply
to save the
settings.
After the DHCP reservation is saved, the DHCP reservations list displays the
configuration.
3.2.5
LAN IPv6
Choose
Setup
>
LAN IPv6
.
The page shown in the following figure appears.This
page allows you to config IPv6 LAN.
The following table describes the parameters of this page.
Field
Description
IPv6 Interface
Address
The address through which PCs access the
19216811.live