36

D-Link DSL-2740B ADSL2+ Modem with Wireless N 300 Router

Section 6 - Setup

Setup Summary (Bridging)

Confirm the settings on this page match the settings provided by your ISP.

To make any changes, click

Back

.

If your settings are correct, click

Apply

.

Note:

After clicking

Apply

, you will have to reboot the router in order to activate your connection.

37

D-Link DSL-2740B ADSL2+ Modem with Wireless N 300 Router

Section 6 - Setup

Wireless Settings

If you want to configure the wireless settings on your router using

the wizard, click Wireless Connection Setup Wizard.

Click Add Wireless Device with WPS If you want to add a wireless

device using Wi-Fi Protected Setup (WPS)

This section allows you to configure your wireless settings by using the

Wireless Connection Setup Wizard

or by doing it manually by selecting

Add Wireless Device with WPS

.

38

D-Link DSL-2740B ADSL2+ Modem with Wireless N 300 Router

Section 6 - Setup

Wireless Connection Setup Wizard

Network

Name SSID:

Network Key:

WPA:

TheSSID(ServiceSetIdentification)istheuniquenameshared

among all devices in a wireless network.

The SSID must be

identical for all devices in the wireless network.

You can either have an automatically assigned network key, or

choose Manually assign a network key to create one yourself.

Select this option for a higher level of wireless security.

Click

Next

Review your wireless settings and click Save to finish the

Setup Wizard.

39

D-Link DSL-2740B ADSL2+ Modem with Wireless N 300 Router

Section 6 - Setup

Wi-Fi Protected Setup

Select Auto to add a wireless client using WPS.

Once you select Auto and click Connect, you will have a 120 second time limit to apply the settings

to your wireless client(s) and successfully establish a connection.

If you select Manual, you will be prompted to enter a Network Name (SSID) and Network Key. Click Next and a settings summary screen will appear.

Write down the security key and enter this on your wireless clients.

Pin:

PBC:

Select this option to use PIN method.

In order to use this method

youmustknowthewirelessclient’s8digitPINandclickConnect.

Select this option to use PBC (Push Button) method to add a

wireless client.

Click Connect.

40

D-Link DSL-2740B ADSL2+ Modem with Wireless N 300 Router

Section 7 - Advanced Setup

Manual Wireless Setup

Enable Wireless:

Wireless Network

Name

(SSID):

Country:

Wireless Channel:

802.11 Mode:

Bandwidth:

If you would like to make wireless available, you must check this box

first.

The SSID (Service Set Identification) is the unique name shared among

all devices in a wireless network.

The SSID must be identical for all

devices in the wireless network.

The channel will adjust according to nations to adapt to each nation’s

frequency provision.

Auto setting can be selected to allow the device to choose the channel

with the least amount of interference.

Select one of the following:

802.11g Only

– Select if all of your wireless clients are 802.11g.

Mixed 802.11g and 802.11b –

Select if you are using both 802.11g

and 802.11b wireless clients.

802.11b Only –

Select if all of your wireless clients are 802.11b.

802.11n Only –

Select if all of your wireless clients are 802.11n.

Mixed 802.11n, 802.11b, and 802.11g –

Select if you are using a mix

of 802.11n, 11g, and 11b wireless clients.

Select the channel width:

Auto 20/40 –

Select if you are using both 802.11n and non-802.11n

wireless devices.

20MHz –

Select if you are not using any 802.11n wireless clients.

This

is the default setting.