D-Link DSL-225 Router Manual PDF (Setup & Configuration Guide)

Page 26 / 154 Scroll up to view Page 21 - 25

D-Link DSL-225 11N VDSL2 Router User Manual

Web User Interface Configuration

Page 26

After clicking the

configure the

WAN Service Configuration

.

Select the

WAN service type

.

Click

IP over Ethernet

or click

Bridge

.

When you click

IP over Ethernet

, the

Enter

Service Description

field changes to

ipoe_0_1_1

. When you click

Bridge

, the

Enter Service Description

field changes to

br_0_1_1

.

For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For

untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID.

Enter a value in the

Enter 802.1P Priority [07]

field.

Enter a value in the

Enter 802.1Q VLAN ID [0-4094]

field.

Select a

TPID VLAN

from the drop-down menu. Select either

0x8100

,

0x88A8

, or

0x9100

.

Select the

Internet Protocol Selection

from the drop-down menu. Select either

IPv4

Only

,

IPv4&IPv6(Dual Stack)

, or

IPv6 Only

.

Click the

Back

button to return to the previous page.

Click the

Page 27 / 154

D-Link DSL-225 11N VDSL2 Router User Manual

Web User Interface Configuration

Page 27

The PPP Username and Password Configuration window opens.

The following parameters can be configured:

PPP Username

: Enter the username provided by your ISP

PPP Password

: Enter the password provided by your ISP

PPPoE Service Name

: Enter the PPPoE service name provided by your ISP

Authentication Method

: From the drop-down list select either

AUTO

,

PAP

,

CHAP

,

MSCHAP

Enable Fullcone NAT

: Tick this option to enable the full-cone NAT feature. If

checked, a warning message appears,

ONLY IF REQUIRED

—

DISABLES

NETWORK ACCELERATION AND SOME SECURITY

Dial on demand (with idle timeout timer)

: Tick this option to enable the dial-on-

demand feature. After selecting this option, enter the

Inactivity Timeout

value

used here. This value must be between 1 and 4320 minutes. By default, this

value is

0

.

PPP IP extension:

Tick this option to enable the PPP IP extension feature.

Use Static IPv4 Address

: Tick this option to manually enter and use a

Static IPv4

Address

.

Enable PPP Debug Mode

: Tick this option to enable the PPP debug mode feature.

Bridge PPPoE Frames Between WAN and Local Ports

: Tick this option to enable

the bridging of PPPoE frames between WAN and the local ports.

Enable IGMP

Multicast Proxy

: Tick this option to enable the IGMP multicast proxy feature.

Click the

Back

button to return to the previous page.

Click the

Page 28 / 154

D-Link DSL-225 11N VDSL2 Router User Manual

Web User Interface Configuration

Page 28

Once you selected from the options above, click the

will be displayed. Here we can configure the interface’s parame

ters.

In the

Routing

–

Default Gateway

section, select the

Default Gateway Interface

.

Click

Page 29 / 154

D-Link DSL-225 11N VDSL2 Router User Manual

Web User Interface Configuration

Page 29

The

DNS Server Configuration

window appears.

The option

Select DNS Server Interface

from available WAN interfaces is already

selected.

Select the

Selected DNS Server Interfaces

.

Choose

Use the following Static DNS IP address

.

Enter a

Primary DNS server

in the field provided and/or

Secondary DNS

.

Click the

Page 30 / 154

D-Link DSL-225 11N VDSL2 Router User Manual

Web User Interface Configuration

Page 30

After clicking the

a summary of the interface’s parameters.

Click the

Back

button to return to the previous page.

Click the

Apply/Save

button to accept the changes.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share