1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DIR-818LW
    5. /
  5. 22
Page 106 / 190 Scroll up to view Page 101 - 105
D-Link DIR-818LW User Manual
101
Section 3 - Configuration
IPv6.over.PPPoE
After selecting the IPv6 over PPPoE option, the user will be able to configure the
IPv6 Internet connection that requires a username and password to get online.
Most DSL modems use this type of connection.
The following parameters will be available for configuration:
PPPoE Session:
Select the PPPoE Session value used here. This
option will state that this connection shares it’s
information with the already configured IPv6
PPPoE connection, or the user can create a new
PPPoE connection here.
User Name:
Enter the PPPoE username used here. If you do not
know your user name, please contact your ISP.
Password:
Enter the PPPoE password used here. If you do not
know your password, please contact your ISP.
Verify Password:
Re-enter the PPPoE password used here.
Service Name:
Enter the service name for this connection here.
This option is optional.
Page 107 / 190
D-Link DIR-818LW User Manual
102
Section 3 - Configuration
Static.IPv6.Address.Connection
This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your
IPv6 configuration settings. You must enter the IPv6 address, Subnet Prefix Length, Default Gateway, Primary DNS Server, and Secondary DNS
Server. Your ISP provides you with all this information.
Use Link-Local
Address:
IPv6 Address:
Subnet Prefix
Length:
Default Gateway:
Primary IPv6 DNS
Address:
Secondary IPv6 DNS
Address:
LAN IPv6 Address:
The Link-local address is used by nodes and routers
when communicating with neighboring nodes on the
same link. This mode enables IPv6-capable devices to
communicate with each other on the LAN side.
Enter the WAN IPv6 address for the router here.
Enter the WAN subnet prefix length value used here.
Enter the WAN default gateway IPv6 address used here.
Enter the WAN primary DNS Server address used here.
Enter the WAN secondary DNS Server address used here.
These are the settings of the LAN (Local Area Network)
IPv6 interface for the router. The router’s LAN IPv6
Address configuration is based on the IPv6 Address and
Subnet assigned by your ISP. (A subnet with prefix /64 is
supported in LAN.)
Page 108 / 190
D-Link DIR-818LW User Manual
103
Section 3 - Configuration
The following parameters will be available for configuration:
6rd IPv6 Prefix:
Enter the 6rd IPv6 address and prefix value used
here.
IPv4 Address:
Enter the IPv4 address used here.
Mask Length:
Enter the IPv4 mask length used here.
Assigned IPv6 Prefix:
Displays the IPv6 assigned prefix value here.
6rd Border Relay IPv4
Address:
Enter the 6rd border relay IPv4 address used here.
IPv6 DNS Server:
Enter the primary DNS Server address used here.
The IPv6 Internet Connection Setup Wizard is complete.
Click on the
Connect
button to continue. Click on the
Prev
button to return to
the previous page. Click on the
Cancel
button to discard all the changes made
and return to the main page.
Tunneling.Connection.(6rd)
After selecting the Tunneling Connection (6rd) option, the user can configure the IPv6 6rd connection settings.
Page 109 / 190
D-Link DIR-818LW User Manual
104
Section 3 - Configuration
IPv6 Manual Setup
There are several connection types to choose from: Auto Detection, Static IPv6, Autoconfiguration (SLAAC/DHCPv6), PPPoE,
IPv6 in IPv4 Tunnel, 6to4, 6rd, and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet
Service Provider.
Note:
If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed
or disabled.
Auto Detection
Select
Auto.Detection
to have the router detect and automatically
configure your IPv6 setting from your ISP.
Page 110 / 190
D-Link DIR-818LW User Manual
105
Section 3 - Configuration
Static IPv6
Select
Static.IPv6
from the drop-down menu.
Enter the address settings supplied by your Internet
provider (ISP).
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select
Stateful.(DHCPv6)
,
SLAAC.+.RDNSS
or
SLAAC.
+.Stateless.DHCPv6
.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
WAN IPv6 Address
Settings:
LAN IPv6 Address:
LAN Link-Local Address:
Enable
Autoconfiguration:
Autoconfiguration Type:
IPv6 Address Lifetime:

Rate

3.5 / 5 based on 2 votes.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top