Page 41 / 122
                                                    Scroll up to view Page 36 - 40
                                                
                    
36
D-Link DIR-652 User Manual
Section 3 - Configuration
Static IPv6 (Stateless)
Select 
Static.IPv6
from the drop-down menu.
Enter the address settings supplied by your Internet 
provider (ISP). 
Enter the LAN (local) IPv6 address for the router. 
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select either 
SLAAC.+.RDNSS
or 
SLAAC.+.Stateless.
DHCPv6
. 
Enter the Router Advertisement Lifetime (in 
minutes).
My IPv6 Connection:
WAN IPv6 Address 
Settings:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconfiguration:
Autoconfiguration Type:
Router Advertisement 
Lifetime:
 
                 
                                
                    
                        Page 42 / 122
                                            
                    
37
D-Link DIR-652 User Manual
Section 3 - Configuration
Autoconfiguration (Stateful)
Select 
Autoconfiguration.(Stateless/DHCPv6)
from 
the drop-down menu.
Select either 
Obtain.DNS.server.address.automatically
or 
Use.the.following.DNS.Address
.
Enter the primary and secondary DNS server addresses. 
Enter the LAN (local) IPv6 address for the router. 
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select 
Stateful.(DHCPv6)
. 
Enter the start IPv6 Address for the DHCPv6 range for 
your local computers.
Enter the end IPv6 Address for the DHCPv6 range for 
your local computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
IPv6 DNS Settings:
Primary/Secondary DNS 
Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconfiguration:
Autoconfiguration Type:
IPv6 Address Range Start:
IPv6 Address Range End:
IPv6 Address Lifetime:
 
                 
                                
                    
                        Page 43 / 122
                                            
                    
38
D-Link DIR-652 User Manual
Section 3 - Configuration
Autoconfiguration (Stateless)
Select 
Autoconfiguration.(Stateless/DHCPv6)
from 
the drop-down menu.
Select either 
Obtain.DNS.server.address.automatically
or 
Use.the.following.DNS.Address
.
Enter the primary and secondary DNS server addresses. 
Enter the LAN (local) IPv6 address for the router. 
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select either 
SLAAC.+.RDNSS
or 
SLAAC.+.Stateless.
DHCPv6
. 
Enter the Router Advertisement Lifetime (in minutes).
My IPv6 Connection:
IPv6 DNS Settings:
Primary/Secondary DNS 
Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconfiguration:
Autoconfiguration Type:
Router Advertisement 
Lifetime:
 
                 
                                
                    
                        Page 44 / 122
                                            
                    
39
D-Link DIR-652 User Manual
Section 3 - Configuration
PPPoE (Stateful)
Select 
PPPoE
from the drop-down menu.
Enter the PPPoE account settings supplied by your Internet provider (ISP). 
Select 
Static
if your ISP assigned you the IP address, subnet mask, gateway, 
and DNS server addresses. In most cases, select 
Dynamic
.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password in the next box.
Enter the ISP Service Name (optional).
Select either 
Always-on
, 
On-Demand
, or 
Manual
.
Enter a maximum idle time during which the Internet connection is 
maintained during inactivity. To disable this feature, enable Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal 
performance with your specific ISP. 1492 is the default MTU.
Select either 
Obtain. DNS. server. address. automatically
or 
Use. the.
following.DNS.Address
.
Enter the primary and secondary DNS server addresses. 
Enter the LAN (local) IPv6 address for the router. 
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
My IPv6 Connection:
PPPoE:
Address Mode:
IP Address:
User Name:
Password:
Service Name:
Reconnection Mode:
Maximum Idle Time: 
MTU:
IPv6 DNS Settings:
Primary/Secondary DNS 
Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconfiguration:
 
                 
                                
                    
                        Page 45 / 122
                                            
                    
40
D-Link DIR-652 User Manual
Section 3 - Configuration
Autoconfiguration Type:
IPv6 Address Range Start:
IPv6 Address Range End:
IPv6 Address Lifetime:
Select 
Stateful.(DHCPv6)
.
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
Enter the IPv6 Address Lifetime (in minutes).