D-Link DIR-652 Router Manual PDF (Setup & Configuration Guide)

Page 31 / 122 Scroll up to view Page 26 - 30

26

D-Link DIR-652 User Manual

Section 3 - Conﬁguration

Enter the IP address assigned by your ISP.

Enter the Subnet Mask assigned by your ISP.

Enter the Gateway assigned by your ISP.

The DNS server information will be supplied by your ISP (Internet Service Provider.)

Maximum Transmission Unit - you may need to change the MTU for optimal

performance with your speciﬁc ISP. 1500 is the default MTU.

The default MAC Address is set to the Internet port’s physical interface MAC

address on the Broadband Router. It is not recommended that you change the

default MAC address unless required by your ISP. You can use the

Clone.Your.PC’s.

MAC.Address

button to replace the Internet port’s MAC address with the MAC

address of your Ethernet card.

IP Address:

Subnet Mask:

Default Gateway:

DNS Servers:

MTU:

MAC Address:

Static (assigned by ISP)

Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask,

gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the ﬁelds must be in the appropriate IP form, which

are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.

Page 32 / 122

27

D-Link DIR-652 User Manual

Section 3 - Conﬁguration

Select the

DS-Lite.DHCPv6.Option

to let the router allocate the AFTR IPv6

address automatically. Select the

Manual.Conﬁguration

to enter the AFTR

IPv6 address in manually.

After selecting the Manual Conﬁguration option above, the user can enter

the AFTR IPv6 address used here.

Enter the B4 IPv4 address value used here.

Once connected, the WAN IPv6 address will be displayed here.

Once connected, the IPv6 WAN Default Gateway address will be displayed

here.

DS-Lite

Conﬁguration:

AFTR IPv6

Address:

B4 IPv4

Address:

WAN IPv6

Address:

IPv6 WAN

Default

Gateway:

DS-Lite

Another Internet Connection type is DS-Lite.

Click on the Save Settings button to accept the changes made.

Click on the Don’t Save Settings button to discard the changes made.

Page 33 / 122

28

D-Link DIR-652 User Manual

Section 3 - Conﬁguration

Check the box to enable the wireless function. If you do not want to use wireless,

uncheck the box to disable all the wireless functions.

The schedule of time when the wireless settings rules will be enabled. The schedule

may be set to

Always

, which will allow the particular service to always be enabled.

You can create your own times in the

Tools

>

Schedules

section.

Service Set Identifier (SSID) is the name of your wireless network. Create a name

using up to 32 characters. The SSID is case-sensitive.

The

Auto.Channel.Scan

setting can be selected to allow the DIR-652 to choose the

channel with the least amount of interference.

Indicates the channel setting for the DIR-652. By default the channel is set to 6. The

Channel can be changed to ﬁt the channel setting for an existing wireless network

or to customize the wireless network. If you enable

Auto.Channel.Scan

, this option

will be greyed out.

Select one of the following:

802±11g.Only

- Select if all of your wireless clients are 802.11g.

802±11n.Only

- Select only if all of your wireless clients are 802.11n.

Mixed.802±11n.and.802±11g

- Select if you are using a mix of 802.11n and 11g

wireless clients.

Select the Channel Width:

Auto.20/40

- This is the default setting. Select if you are using

both 802.11n and non-802.11n wireless devices.

20MHz

- Select if you are not using any 802.11n wireless clients.

40MHz

- Select if using only 802.11n wireless clients.

Select the transmit rate. It is strongly suggested to select

Best.(Auto)

for best

performance.

Select

Invisible

if you do not want the SSID of your wireless network to be

broadcasted by the DIR-652. If Invisible is selected, the SSID of the DIR-652 will

not be seen by Site Survey utilities so your wireless clients will have to know the

SSID of your DIR-652

Enable Wireless:

Enable Auto Channel

Scan:

Wireless Settings

Wireless Network

Name:

Wireless Channel:

802.11 Mode:

Channel Width:

Transmission Rate:

Visibility Status:

Schedule:

Page 34 / 122

29

D-Link DIR-652 User Manual

Section 3 - Conﬁguration

This section will allow you to change the local network settings of the router and to conﬁgure the DHCP settings.

Network Settings

Enter the IP address of the router. The default IP address is

192.168.0.1.

If you change the IP address, once you click

Apply

, you will need

to enter the new IP address in your browser to get back into the

conﬁguration utility.

Enter the Subnet Mask. The default subnet mask is 255.255.255.0.

Enter the Domain name (Optional).

Uncheck the box to transfer the DNS server information from your

ISP to your computers. If checked, your computers will use the

router for a DNS server.

IP Address:

Subnet Mask:

Local Domain:

Enable DNS Relay:

Page 35 / 122

30

D-Link DIR-652 User Manual

Section 3 - Conﬁguration

DHCP Server Settings

DHCP stands for Dynamic Host Control Protocol. The DIR-652 has a built-in DHCP server. The DHCP Server will automatically assign an IP address

to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP

Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-652. The

DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting

and ending address of the IP address pool.

Check this box to enable the DHCP server on your router. Uncheck

to disable this function.

Enter the starting and ending IP addresses for the DHCP server’s

IP assignment.

Note:

If you statically (manually) assign IP addresses to your

computers or devices, make sure the IP addresses are outside of this

range or you may have an IP conﬂict.

The length of time for the IP address lease. Enter the Lease time

in minutes.

Enable this feature to broadcast your networks DHCP server to

LAN/WLAN clients.

NetBIOS allows LAN hosts to discover all other computers within

the network, enable this feature to allow the DHCP Server to oﬀer

NetBIOS conﬁguration settings.

Enable this feature to allow WINS information to be learned from

the WAN side, disable to allow manual conﬁguration.

This feature allows the conﬁguration of a NetBIOS ‘domain’ name under which network hosts operates. This setting has no eﬀect if the ‘Learn NetBIOS information

from WAN’ is activated.”

Select the diﬀerent type of NetBIOS node:

Broadcast.only

,

Point-to-Point

,

Mixed-mode

, and

Hybrid

.

Enter your Primary (and Secondary) WINS IP address(es).

Enable DHCP

Server:

DHCP IP Address

Range:

DHCP Lease Time:

Always Broadcast:

NetBIOS

Announcement:

Learn NetBIOS

from WAN:

NetBIOS Scope:

NetBIOS Mode

Type:

Primary/Secondary

WINS IP Address:

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share