Page 31 / 97
Scroll up to view Page 26 - 30
31
D-Link DIR-600 User Manual
Section 3 - Con±guration
This section will allow you to change the local network settings of the router and to con±gure the DHCP settings.
LAN Setup
Enter the IP address of the router. The default
If you change the IP address, once you click
Apply
, you will need to enter the new IP address
in your browser to get back into the con±guration
utility.
Enter the Subnet Mask. The default subnet mask
is 255.255.255.0.
Enter the Domain name (Optional).
Check the box to transfer the DNS server
information from your ISP to your computers. If
unchecked, your computers will use the router
for a DNS server.
Address:
DefaultSubnet
Mask:
LocalDomain
Name:
EnableDNS
Relay:
Refer to the next page for DHCP information.
Page 32 / 97
32
D-Link DIR-600 User Manual
Section 3 - Con±guration
Check the box to enable the DHCP server on
your router. Uncheck to disable this function.
Enter the starting and ending IP addresses for
the DHCP server’s IP assignment.
The length of time for the IP address lease.
Enter the Lease time in minutes.
leDHCP
Server:
DHCPIP
Address Range:
DHCPLease
Time:
DHCPServerSettings
DHCP stands for Dynamic Host Control Protocol.
The DIR-600 has a built-in DHCP server. The DHCP
Server will automatically assign an IP address to the
computers on the LAN/private network. Be sure to
set your computers to be DHCP clients by setting
their TCP/IP settings to “Obtain an IP Address
Automatically.” When you turn your computers
on, they will automatically load the proper TCP/IP
settings provided by the DIR-600. The DHCP Server
will automatically allocate an unused IP address from
the IP address pool to the requesting computer. You
must specify the starting and ending address of the
IP address pool.
Page 33 / 97
33
D-Link DIR-600 User Manual
Section 3 - Con±guration
This section will allow you to con±gure, update, and maintain the correct time on the internal system clock.
TimeandDate
Select the Time Zone from the drop-down
menu.
Ticking this checkbox enables Daylight Saving
time. Click
Sync. your computer’s time
settings
to copy your PC’s time settings.
Tick the “Automatically synchronize with
D-Link’s Internet time server” checkbox and
then use the drop-down menu to select an NTP
Server. NTP is short for Network Time Protocol.
NTP synchronizes computer clock times in a
network of computers.
To manually input the time, enter the values
in these fields for the Year, Month, Day, Hour,
Minute, and Second. Click
SaveSettings
.
Zone:
Enable
Daylight
Saving:
NTP
Server
Used:
Manual:
Page 34 / 97
34
D-Link DIR-600 User Manual
Section 3 - Con±guration
This feature allows you to create a list of websites that you want to either allow or deny users access.
Parental Control
Select Turn Parental Control OFF, Turn Parental
Control ON and ALLOW computers access to
ONLY these sites, or Turn Parental Control ON
and DENY computers access to ONLY these
sites.
Enter the keywords or URLs that you want to
block (or allow). Any URL with the keyword in
it will be blocked.
The schedule of time when the parental control
±lter will be enabled. The schedule may be set
to Always, which will allow the particular service
to always be enabled. You can create your
own times in the
Maintenance
>
Schedules
section.
Parental
Control:
Website URL:
Schedule:
Page 35 / 97
35
D-Link DIR-600 User Manual
Section 3 - Con±guration
Port Forwarding
This will allow you to open a single port or a range of ports.
Check the box to enabled the rule.
Enter a name for the rule.
Enter the IP address of the computer on your local
network that you want to allow the incoming service
to.
Enter the port or ports that you want to open. If
you want to open one port, enter the same port in
both boxes.
Select TCP, UDP, or Any
Name:
IP Address:
Start Port/
End Port:
Traffic Type:
19216811.live