D-Link DIR-600M Router Manual PDF (Setup & Configuration Guide)

Page 21 / 97 Scroll up to view Page 16 - 20

21

D-Link DIR-600 User Manual

Section 3 - Con±guration

Select

Dynamic

(most common) or

Static

. Select

Static

if your

ISP assigned you the IP address, subnet mask, gateway, and

DNS server addresses.

Enter your PPPoE user name.

Enter your PPPoE password and then retype the password in

the next box.

Enter the ISP Service Name (optional).

Enter the IP address (Static PPPoE only).

Enter the Primary and Secondary DNS Server Addresses (Static

PPPoE only).

Enter a maximum idle time during which the Internet connection

is maintained during inactivity. To disable this feature,

enable Auto-reconnect.

Maximum Transmission Unit - You may need to change the

MTU for optimal performance with your specific ISP. 1492 is

the default MTU.

Select either

Always-on

,

Manual

, or

Connect-on

demand

.

oE:

User Name:

Password:

Service฀Name:

IP Address:

DNS฀

Addresses:

Maximum Idle

Time:

MTU:

Connection

Mode Select:

Internet Setup

PPPoE

Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide

you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE

software from your computer. The software is no longer needed and will not work through a router.

Page 22 / 97

22

D-Link DIR-600 User Manual

Section 3 - Con±guration

Select

Dynamic

(most common) or

Static

. Select

Static

if

your ISP assigned you the IP address, subnet mask, gateway,

and DNS server addresses.

Enter the IP address (Static PPTP only).

Enter the Primary and Secondary DNS Server Addresses

(Static PPTP only).

Enter the Gateway IP Address provided by your ISP.

The DNS server information will be supplied by your ISP

(Internet Service Provider.)

Enter the Server IP provided by your ISP (optional).

Enter your PPTP account name.

Enter your PPTP password and then retype the password

in the next box.

Enter a maximum idle time during which the Internet

connection is maintained during inactivity. To disable this

feature, enable Auto-reconnect.

Maximum Transmission Unit - You may need to change the

MTU for optimal performance.

Select either Always-on, Manual, or Connect-on demand.

IP Address:

Subnet Mask:

Gateway:

DNS:

Internet Setup

PPTP

Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with

a username and password. This option is typically used for DSL services.

ver฀IP:

PPTP Account:

PPTP Password:

Maximum Idle

Time:

MTU:

Connect Mode:

Page 23 / 97

23

D-Link DIR-600 User Manual

Section 3 - Con±guration

Select

Dynamic

(most common) or

Static

. Select

Static

if your ISP assigned you the IP address, subnet mask,

gateway, and DNS server addresses.

Enter the IP address (Static L2TP only).

Enter the Primary and Secondary DNS Server Addresses

(Static L2TP only).

Enter the Gateway IP Address provided by your ISP.

The DNS server information will be supplied by your ISP

(Internet Service Provider.)

Enter the Server IP provided by your ISP (optional).

Enter your L2TP account name.

Enter your L2TP password and then retype the password

in the next box.

Enter a maximum idle time during which the Internet

connection is maintained during inactivity. To disable this

feature, enable Auto-reconnect.

Maximum Transmission Unit - You may need to change the

MTU for optimal performance with your speci±c ISP.

Select either Always-on, Manual, or Connect-on demand.

IP Address:

Subnet Mask:

Gateway:

DNS:

Server฀IP:

L2TP Account:

L2TP

Password:

Maximum Idle

Time:

MTU:

Connect Mode:

Internet Setup

L2TP

Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a

username and password. This option is typically used for DSL services.

Page 24 / 97

24

D-Link DIR-600 User Manual

Section 3 - Con±guration

Internet Setup

Dual฀Access฀(for฀Russia฀only)

There are two main steps to configure a Dual Access Internet connection for Russia. First, configure a PPPoE connection (as previously

described for PPPoE connections), and add the physical WAN IP settings as instructed from the ISP. Second, con±gure a PPTP connection

(as previously described for PPTP connections). In addition, the second step also includes an option to use a MAC address that will always

be associated with the connection. The MAC address is entered manually or copied from the computer.

Page 25 / 97

25

D-Link DIR-600 User Manual

Section 3 - Con±guration

Wireless Setup

Wireless settings for the router may be configured

manually or by using a wizard. To use the wizard,

click the

Wireless฀Connection฀Setup฀Wizard

button

and then follow the steps that are described below.

To configure the wireless settings manually, click

the

Manual Wireless Connection

Setup

button.

The parameters for this window are described later

in this section. The Wireless Security section that

directly follows this Configuration section provides

additional explanation for how to con±gure the WEP,

WPA, WPA2, and WPA/WPA2 wireless security

mode options.

Click

Enter a Wireless Network Name in the textbox, which

is also know as the SSID and select the desired level

of wireless security, WEP, WPA. and then click

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share