D-Link DIR-600M Router Manual PDF (Setup & Configuration Guide)

Page 16 / 97 Scroll up to view Page 11 - 15

16

D-Link DIR-600 User Manual

Section 3 - Con±guration

Select your time zone and NTP-server from the drop-down menu

and then click

Select the type of Internet connection you use and then click

If you selected Dynamic, you may need to enter the MAC address of the

computer that was last connected directly to your modem. If you are currently

using that computer, click

Clone Your PC’s MAC Address

and then click

The Host Name is optional but may be required by some ISPs. The default

host name is the device name of the Router and may be changed.

Page 17 / 97

17

D-Link DIR-600 User Manual

Section 3 - Con±guration

If you selected PPPoE, enter your PPPoE username and password. Click

Select

Static

if your ISP assigned you the IP address, subnet mask,

gateway, and DNS server addresses.

Note:

Make sure to remove your PPPoE software from your computer. The

software is no longer needed and will not work through a router.

If you selected PPTP, enter your PPTP username and password. Click

If you selected L2TP, enter your L2TP username and password. Click

Page 18 / 97

18

D-Link DIR-600 User Manual

Section 3 - Con±guration

If you selected Static, enter your network settings supplied by your Internet

provider. Click

Click

Connect

to save your settings.

Please allow 1-2 minutes for rebooting. When the router has finished

rebooting, the opening window will be displayed.

Page 19 / 97

19

D-Link DIR-600 User Manual

Section 3 - Con±guration

Enter the IP address assigned by your ISP.

Enter the Subnet Mask assigned by your ISP.

Enter the Gateway assigned by your ISP.

The default MAC Address is set to the WAN’s physical

interface MAC address on the Broadband Router. It is not

recommended that you change the default MAC address

unless required by your ISP.

The default MAC address is set to the WAN’s physical

interface MAC address on the Broadband Router. You

can use the

Clone MAC Address

button to copy the MAC

address of the Ethernet Card installed by your ISP and

replace the WAN MAC address with the MAC address of the

router. It is not recommended that you change the default

MAC address unless required by your ISP.

Enter the Primary DNS server IP address assigned by your

ISP.

This is optional.

Maximum Transmission Unit - you may need to change the

MTU for optimal performance with your specific ISP. 1492

is the default MTU.

dress:

Subnet Mask:

ISP Gateway

Address:

MAC Address:

Clone MAC

Address:

Primary฀DNS฀

Address:

Secondary฀DNS฀

Address:

MTU:

Internet Setup

Static (assigned by ISP)

Select Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask,

gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP

form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.

Page 20 / 97

20

D-Link DIR-600 User Manual

Section 3 - Con±guration

The Host Name is optional but may be required by some

ISPs. The default host name is the device name of the

Router and may be changed.

The default MAC Address is set to the WAN’s physical

interface MAC address on the Broadband Router. It is not

recommended that you change the default MAC address

unless required by your ISP.

The default MAC address is set to the WAN’s physical

interface MAC address on the Broadband Router. You

can use the “Clone MAC Address” button to copy the MAC

address of the Ethernet Card installed by your ISP and

replace the WAN MAC address with the MAC address of the

router. It is not recommended that you change the default

MAC address unless required by your ISP.

Enter the DNS (Domain Name Server) server IP address

assigned by your ISP.

Name:

MAC Address:

Internet Setup

Dynamic

C

Address:

Primary /

Secondary

DNS฀

Addresses:

MTU:

Maximum Transmission Unit - You may need to change the MTU for optimal performance with your speci±c ISP.

Point

Mode:

Checking this box disables NAT and turns the Router into

an Access Point only.

To manually set up the Internet connection, click the

Manual Internet Connection Setup

button on the Router’s

opening window.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share