Page 36 / 171
Scroll up to view Page 31 - 35
31
D-Link DHP-1565 User Manual
Section 3 - Configuration
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can use the Clone Your PC’s MAC Address button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
MAC Address:
Click the
Save Settings
button to save any changes made.
Page 37 / 171
32
D-Link DHP-1565 User Manual
Section 3 - Configuration
Select
Static IP
if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic IP
.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses (Static
PPTP only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your PPTP username.
Enter your PPTP password and then retype the password in the
next box.
Use the radio buttons to specify the reconnect mode. The
user can
specify a custom schedule or specify the
On Demand
, or
Manual
option.
Enter a maximum idle time during which the Internet connection
is maintained during inactivity. To disable this feature, enable Auto-reconnect.
Address Mode:
PPTP IP
Address:
PPTP Subnet
Mask:
PPTP Gateway
IP Address:
PPTP Server IP
Address:
Manual Internet Connection Setup
PPTP
Username:
Password:
Reconnect
Mode:
Maximum Idle
Time:
Select
PPTP (Point-to-Point Tunneling Protocol)
from the drop-down menu if your ISP uses a PPTP connection. Your ISP will
provide you with a username and password. This option is typically used for DSL services.
Page 38 / 171
33
D-Link DHP-1565 User Manual
Section 3 - Configuration
The DNS server information will be supplied by your ISP (Internet Service Provider).
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can use the
Clone Your PC’s MAC Address
button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
DNS Servers:
MTU:
MAC Address:
Click the
Save Settings
button to save any changes made.
Page 39 / 171
34
D-Link DHP-1565 User Manual
Section 3 - Configuration
Select Static if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases,
select Dynamic.
Enter the L2TP IP address supplied by your ISP (Static only).
Enter the Subnet Mask supplied by your ISP (Static only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your L2TP username.
Enter your L2TP password and then retype the password in
the next box.
Use the radio buttons to specify the reconnect mode. The
user
can specify a custom schedule or specify the
On Demand
, or
Manual
option.
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.
Address Mode:
L2TP IP Address:
L2TP Subnet
Mask:
Manual Internet Connection Setup
L2TP
Choose
L2TP
(Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option
is typically used for DSL services.
L2TP Gateway
IP Address:
L2TP Server IP
Address:
Username:
Password:
Reconnect
Mode:
Maximum Idle
Time:
Page 40 / 171
35
D-Link DHP-1565 User Manual
Section 3 - Configuration
Primary DNS
Server:
MTU:
MAC Address:
Enter the Primary DNS server IP address assigned by your ISP. These address is usually obtained automatically from your ISP. Enter
the value 0.0.0.0 if you did not specifically receive these from your ISP.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can use the
Clone Your PC’s MAC Address
button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
19216811.live