Page 26 / 72
Scroll up to view Page 21 - 25
±µ
D-Link DCS-910/9±0 User Manual
Section ² - Configuration
Setup > Wireless
Service Set Identifier, an identifier for your wireless network.
The default setting is channel 6. Select the same channel that is using by other wireless devices within your network. When there is
interference from the wireless networks that overlap with one another, you may change the channel to obtain maximum performance
for your connection.
Infrastructure
is a wireless connection using an access point as a transmission point of all wireless devices.
Ad-Hoc
is a wireless
connection used without an access point, where your DCS-920 is directly connecting to your PC. This is done using the on-
board wireless adapter on the DCS-920 connected to a wireless adapter on the PC.
This page will allow you to select a wireless network that the DCS-920 was able to detect upon booting up.
For security, there are three choices;
None
,
WEP
, and
WPA-PSK / WPA2-PSK
. Select the same encryption method that is being
used by your wireless device/ router.
An appropriate
Preshared Key
, which is needed in order to connect to the wireless network..
SSID:
Channel:
Connection Mode:
Survey:
Wireless Security
Mode:
WPA-PSK / WPA2PSK
Settings:
Wireless Interface
In this section, you can setup and configure the wireless
settings on your camera.
Note:
Wireless is available only for the DCS-920.
Page 27 / 72
±¶
D-Link DCS-910/9±0 User Manual
Section ² - Configuration
(Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it
has been modified. The username and password are required when using the DDNS service.
Click to enable the DDNS function.
Select your Dynamic DNS Server from the pull down menu.
Enter the host name of the DDNS server.
Enter your username or e-mail used to connect to the DDNS.
Enter your password used to connect to the DDNS server.
DDNS:
Enable:
Server Address:
Host Name:
User Name:
Password:
Setup > DDNS
In this section, you can configure the DDNS setting
for your camera. DDNS will allow all users to access
your camera using a domain name instead of an IP
address.
Page 28 / 72
±·
D-Link DCS-910/9±0 User Manual
Section ² - Configuration
Setup > Image Setup
Check to enable antiflicker.
Vertically rotates the video. If the camera is installed upside down,
Flip Image
and
Mirror
should both be checked.
Horizontally rotates the video.
Allows you to adjust the brightness level.
Allows you to adjust the contrast level.
Allows you to adjust the saturation level. .
Enable Antiflicker:
Flip Image:
Mirror:
Brightness Control:
Contrast Control:
Saturation Control:
Image Settings
In this section, you can configure the image settings for
your camera.
Page 29 / 72
±9
D-Link DCS-910/9±0 User Manual
Section ² - Configuration
Setup > Video
Video Profile:
Light Frequency:
Video Configuration
Encode Type:
Resolution:
FPS:
Quality:
The compression format used when viewing your camera.
Select the desired video resolution from three formats: 640x480, 320x240, and 160x120. The higher setting can
obtain better quality. However, it will use more resource within your network.
Select the optimal setting depending on your network status. Please note that the higher setting can obtain better
quality. However, it will use more resource within your network.
Select the desired image quality from five levels: Highest, High, Medium, Low, and Lowest.
Select the proper frequency (50Hz or 60Hz) to reduce image flicker.
In this section, you can configure the video settings for
your camera.
This section allows you to change the
Encode Type
,
Resolution
,
FPS
, and
Quality
.
Page 30 / 72
²0
D-Link DCS-910/9±0 User Manual
Section ² - Configuration
Setup > Mail
Email Account
SMTP Server
Address:
Sender e-mail
Address:
Receiver e-mail
Address:
User Name:
Password:
This is the domain name or IP address of your external e-mail
server.
This is the e-mail address of the person sending the camera
snapshots.
This is the e-mail address of recipient for the SMTP server.
If the SMTP server uses authentication, you must enter your user
name here.
This is the password that you use with your user name to connect to
the SMTP server.
In this section, you can configure the email notification settings for
your camera.
19216811.live