Page 11 / 140 Scroll up to view Page 6 - 10
11
The InstallShield will install in
the following folder. To install
into a different folder, click
Browse and select another
folder.
Click
Next
.
Select the Program folder
that Setup will add program
icons to. You may type a new
folder name, or select one
from the existing folders list.
Click
Next
.
Please wait while the
Installation
Wizard
is
installed.
Installation Wizard (continued)
Page 12 / 140
12
Installation is now complete.
Installation Wizard (continued)
IMPORTANT:
A hardware reset of the Internet Camera may be required if the
Installation
Wizard
cannot find the camera. To accomplish this reset, lightly insert a paper
clip (or a similar sized tool) into the reset hole on the back of the camera (see
page 6 for the location of the reset
hole). The LED on the front of the camera
will begin blinking orange. When it stops the blinking cycle continue to hold in
the reset button until a second cycle of blinking red and green lights indicates a
second reset cycle has completed. This will take approximately 5-7 seconds.
The opening Installation Wizard screen
will appear and
show a MAC address of
the
DCS-2000
and an IP Address (which
may or may not be correct depending on
what you have your
DCS-2000
connected
to). If you have a DHCP* server on your
network, there will be a valid IP Address
displayed here, indicated by a “Yes”
under the assigned column.
*A DHCP server is a device that supplies
IP Addresses to its clients that are on the
same network.
Click
Finish
.
To access the Installation Wizard
screen, click on the Installation
Wizard Icon on your desktop.
Page 13 / 140
13
The
Installation Wizard
will now show a MAC address for the
DCS-2000
and
an IP address. This IP address may not be correct at this step in the installation
until you see “Yes” under the assigned column. The camera is now automatically
configured with an IP address consistent to the device it is connected to.
Click on the
Link to Selected
Devices
button.
Select the MAC address.
After you click on the
Link
to Selected Devices
button,
Installation
Wizard
will automatically
open
your
Internet
browser
to
the
IP
Address of the
DCS-
2000
, in this example it is:
DCS-2000
may have a
different IP Address.
You have now completed the Setup Wizard and are ready to use your
camera! You can also continue to the section titled “Installing IP
surveillance Software” (page 21) to install the IP surveillance software
before you begin to use the DCS-2000.
For more information regarding the functions of this screen, see the following
section titled “Installation Wizard Screen.”
Installation Wizard (continued)
Page 14 / 140
14
Installation Wizard Screen
The following options are available on the Installation Wizard screen by clicking
on the corresponding tab:
Search -
Click to search for any available
cameras to connect to the network.
Add -
Click to manually add a camera to
the network. A window will appear,
prompting you to enter the camera’s
IP address or domain name. A
second window will appear,
prompting you to enter the port
number.
Remove -
Click to remove the selected camera(s) from the network.
Uncheck All -
Click to uncheck all selected cameras.
Links to Selected Devices -
Click to link all selected devices to the network.
Setup -
On the initial Setup Screen you can
configure System and Date/Time
settings for each camera. Click
Next
to configure Network settings
for the camera.
System Settings -
Enter a Camera Name and create
a Root password for the camera.
Date/Time Settings -
Enter the Date and Time for each
camera. These settings can also be
configured on the
Tools > System
screen (page 50) when configuring
the camera via a Web browser.
Page 15 / 140
15
Installation Wizard Screen (continued)
Upgrade -
Network Settings -
Here users can configure the
Network Settings for the camera.
Enter the IP address, Subnet mask,
Default router IP, Primary DNS, and
Secondary DNS. Automatically, the
option to reset IP address at boot is
selected. If you would like to save
your IP address settings, make sure
to uncheck this box. These settings
can also be configured on the
Advanced > Network screen
(page 36) when configuring the
camera via a Web Browser.
Click Next and then
Apply
to save
the configured settings. Users can
click
Previous
to modify changes
or mistakes.
The upgrade window allows users
to upload a saved firmware file. If
the firmware is older than that
currently on the camera, a screen
will appear indicating so and
prompting the user to confirm the
upload.
Package Information -
This displays information about the
firmware and plugin currently
installed on the camera.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top