Page 26 / 99 Scroll up to view Page 21 - 25
Chapter 4
Configuration
WBMR-HP-GNV2 User Manual
25
Internet/LAN
Internet
The Internet settings are made here. For details on the settings, refer to the documentation
provided by your ADSL provider.
Page 27 / 99
WBMR-HP-GNV2 User Manual
26
Chapter 4
Configuration
Parameter
Meaning
Internet Setup
Encapsulation
Set the ADSL communication method.
Modulation
Set the modulation system used in ADSL communication.
Multiplexing
Set the encapsulation system for VC multiplexing.
Select from LLC (Logical Link Control Encapsulation) which can
handle multiple protocols or VC (Virtual Circuit) for a single
protocol.
QoS Type
Set the QoS (Quality of Service).
Select from the three service categories (UBR, CBR, VBR) where the
QoS is guaranteed in the band.
PCR Rate
Set the PCR (Peak Cell Rate) when CBR or VBR is selected for QoS
Type. The network upper limit transfer speed is set in the range
from 1 to 65534 cps.
SCR Rate
Set the SCR (Sustainable Cell Rate) when CBR or VBR is selected
for QoS Type. The network sustainable transfer speed is set in the
range from 1 to 65534 cps.
Auto Detect
Set to VPI (Virtual Path Identification) or VCI (Virtual Channel
Identification) of the virtual circuit when Disable is selected for
Auto Detect.
Virtual Circuit
Set automatic detection of the virtual circuit.
Obtain an IP Address
Automatically(DHCP)/Use following
IP Address
This option is displayed when RFC1483 Bridged is selected in the
Encapsulation field.
Select whether the IP address, subnet mask, gateway, and DNS are
obtained automatically or manually.
Internet IP Address
Set the “public” (or “global”) IP address that identifies your
broadband gateway on the Internet.
Subnet Mask
Set the Internet subnet mask.
Gateway
Set the Gateway address specified by the provider.
Primary DNS / Second DNS
Set the DNS server address specified by the provider.
Service Name
Set the service name specified by the provider in 64 or less single-
byte alphanumeric characters.
Page 28 / 99
Chapter 4
Configuration
WBMR-HP-GNV2 User Manual
27
Parameter
Meaning
User Name
Set the user name (PPP login name) specified by the provider in 64
or less single-byte alphanumeric characters and symbols.
If the name specified by the provider contains an @ mark, the
characters after the @ mark cannot be omitted when entering the
User Name.
Password
Set the password specified by the provider in 64 or less single-byte
alphanumeric characters and symbols.
Connect on Demand/Keep Alive
Select the Connect on Demand or Keep Alive.
When Connect on Demand is selected, the AirStation is
automatically connected to the server only when communication is
performed. The connection is disconnected if the communication is
not performed for a preset time (disconnect time).
Set the disconnect time in the range from 1 to 9999 minutes.
When Keep Alive is selected, the AirStation issues an LCP echo
request to the server periodically at preset time intervals, and
the response received from the server is used to confirm that
communication is enabled.
If no response from the server is received, the AirStation assumes
that the line is disconnected, and it disconnects the connection.
Set the Keep Alive time interval in the range from 20 to 180
seconds.
Host Name
Set the host name that is sent to the server when acquiring the IP
address from the Internet.
Domain Name
Set the domain name.
MTU
Set the MTU (Maximum Transmission Unit) that is used in
communication.
Select from Auto or Manual. When set to Manual, the available
range is set from 576 to 1500 bytes.
Network Setup
Local IP Address / Subnet Mask
By default, the LAN side IP address is 192.168.11.1 with subnet
mask 255.255.255.0.
You may change it here.
Local DHCP Server
The factory setting of this control, Enable, sets the gateway to act
as a DHCP server for local machines. When this setting is used, you
can set a range of IP addresses to be assigned by DHCP. Addresses
outside this range can be assigned manually to machines set to use
fixed IP settings.
Page 29 / 99
WBMR-HP-GNV2 User Manual
28
Chapter 4
Configuration
Parameter
Meaning
DHCP Relay Server
When Local DHCP Server is set to DHCP Relay, you must enter
the IP address of the remote DHCP server here. (Note that “DHCP
relay server” is a widely used but incorrect term for a remote DHCP
server.)
Starting IP Address
This is the lowest address in the range that the gateway will assign
by DHCP.
Maximum Number of DHCP Users
This is the number of addresses that can be assigned by DHCP.
Client Lease Time
This is the number of minutes any DHCP client is given exclusive
use of a (non-reserved) DHCP-assigned IP address. This can be from
1 to 9999.
Static DNS 1 / Static DNS 2 / Static DNS
3
Enter the IP address(es) of one to three name servers.
WINS
Enter the IP address of a Windows Internet Name Service server, if
such a server is available to you.
Page 30 / 99
Chapter 4
Configuration
WBMR-HP-GNV2 User Manual
29
DDNS (Router Mode only)
Configure Dynamic DNS settings.
Many settings are only available when the appropriate Dynamic
DNS service is enabled.
Parameter
Meaning
DDNS Service
Select a provider (DynDNS or TZO) for Dynamic DNS.
User Name
Enter the Dynamic DNS user name. You may enter up to 64
alphanumerical characters and symbols.
Password
Enter the Dynamic DNS password. You may enter up to 64
alphanumerical characters and symbols.
Host Name
Enter the Dynamic DNS host name. You may enter up to 255
alphanumerical characters, hyphens, and periods.
Email Address
Enter the email address which is registered to the Dynamic DNS
service. You may enter up to 64 alphanumerical characters and
symbols.
TZO Key
Enter the TZO Key which is registered to the Dynamic DNS service.
You may enter up to 64 alphanumerical characters and symbols.
Domain Name
Enter the domain name which is registered to the Dynamic DNS
service.
You may enter up to 255 alphanumerical characters,
hyphens, and periods.

Rate

4 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top