Page 41 / 166
Scroll up to view Page 36 - 40
IP/Prefix Length:
please type the IP and the prefix length for the IPv6 address from your ISP.
IPv6 Gateway:
Type the gateway to which the WAN packets are forwarded.
Obtain IPv6 DNS:
check Automatic to obtain DNS automatically. If not, please type the concrete
ones in the Primary and Secondary fields.
Pure Bridge Connection
IP TV / VOD applications:
The predefined WAN settings for users. Users can adopt the appropriate
one base on need.
VPI/VCI:
Enter the VPI and VCI information provided by your ISP.
Encap. method:
Select the encapsulation format. Select the one provided by your ISP.
Click Apply to confirm the settings.
Page 42 / 166
EWAN Mode
Step 1: Select WAN port connect mode from the connect mode drop down menu. There are two
types of connect mode to choose from: ADSL or EWAN.
Here select
EWAN
and click
Continue
. If
you only want to configure Wireless, press
Jump to Wireless setting
.
Step 2: there are four availabe protocols.
Each protocol
is described in the following sections
of EWAN Connect mode.
Select the protocol. You can enable or disable VLAN Mux feature, if
enabled, you should enter the 802.1Q VLAN ID. For VLAN MUX setting, please refer to
VLAN MUX
Setting
for help.
Click
Continue
to go on.
Step 3: The device will reboot and then load the new configuration.
38
Page 43 / 166
Step 4: WAN port configuration is sucess, now
Next to Wireless.
Step 5: Enter the ESSID, select the Channel ID and the Security Mode. For security information,
please turn to
WLAN
section in this manual for help.
Step 6: Quick Start is finished.
39
Page 44 / 166
40
EWAN Connect Mode
PPPoE connection
Username:
Enter the username provided by your ISP. You can input up to 256 alphanumeric
characters (case sensitive).
Password:
Enter the password provided by your ISP. You can input up to 32 alphanumeric characters
(case sensitive).
Service Name:
This item is for identification purposes. If it is required, your ISP will provide you the
necessary information. Maximum input is 32 alphanumeric characters.
Authentication Protocol:
Default is Auto. Please consult your ISP on whether to use Chap, Pap or
MSCHAP.
IP Address:
Enter your fixed IP address.
Obtain DNS automatically:
Click to activate DNS and to enable the system to automatically detect
DNS.
Primary DNS / Secondary DNS:
Enter the IP addresses of the DNS servers. The DNS servers are
passed to the DHCP clients along with the IP address and the netmask.
MTU:
Maximum Transmission Unit.
The size of the largest datagram (excluding media-specific
Page 45 / 166
headers) that IP will attempt to send through the interface.
VLAN Mux:
check whether to enable VLAN Mux function.
802.1Q VLAN ID:
It is a parameter to specify the VLAN which the frame belongs. Enter the VLAN
ID identification, tagged: 2-4095.
IPv6:
check to enable IPv6 service. Enter IPv6 Gateway address and set IPv6 DNS as same in IPv4
mode.
IPv6 Address:
type the IPv6 address from your ISP, or get it automatically. ” ::” means to obtain IPv6
address automatically.
Obtain IPv6 DNS:
check Automatic to obtain DNS automatically. If not, please type the concrete
ones in the Primary and Secondary fields.
Obtain an IP Address Automatically
Select this protocol enables the device to automatically obtain IP address.
VLAN Mux:
check whether to enable VLAN Mux function.
802.1Q VLAN ID:
It is a parameter to specify the VLAN which the frame belongs. Enter the VLAN
ID identification, tagged: 2-4095.
IPv6:
Check to enble the function
IPv6 Gateway:
Enter the IP address of the default IPv6 gateway.
41
19216811.live