Billion BiPAC-7700N-R2 Router Manual PDF (Setup & Configuration Guide)

Page 121 / 168 Scroll up to view Page 116 - 120

118

Click

Apply/Save

to confirm your settings and your added group will be listed in the Interface

Grouping table below.

If you want to remove the group, check the box as the following and press

Remove

.

Note:

If you like to automatically add LAN clients to a WAN Interface in the new group add the

DHCP vendor ID string.

By configuring a DHCP vendor ID string any DHCP client request with the specified vendor

ID (DHCP option 60) will be denied an IP address from the local DHCP server.

If a vendor ID is configured for a specific client device, please REBOOT the client device

attached to the modem to allow it to obtain an appropriate IP address.

Each LAN interface can only be added into one group and one WAN interface can only be

used in one group.

Page 122 / 168

119

Multicast

Multicast is one of the three network transmission modes, Unicast, Multicast, Broadcast. It is a

transmission mode that supports point-to-multipoint connections between the sender and the

recipient. IGMP protocol is used to establish and maintain the relationship between IP host and the

host directly connected multicast router.

IGMP stands for

Internet Group Management Protocol

is a communications protocols used to

manage the membership of Internet Protocol multicast groups. IGMP is used by IP hosts and the

adjacent multicast routers to establish multicast group members. There are three versions for IGMP,

that is IGMPv1, IGMPv2 and IGMPv3.

IGMP

Default Version:

enter the supported IGMP version, 1-3, default is IGMP v3.

Query

Interval:

enter the periodic query interval time (sec) the multicast router sending the query

message to hosts to understand the group membership information.

Query

Response

Interval:

enter the response interval time (sec).

Last Member Query Interval:

enter the interval time (sec) the multicast router query the specified

group after it has received leave message.

Robustness Value:

enter the router robustness parameter, 2-7, the greater the robustness value,

the more robust the Querier is.

Maximum Multicast Groups:

enter the Maximum Multicast Groups.

Maximum Multicast Data Sources( for IGMP v3):

enter the Maximum Multicast Data Sources,1-24.

Maximum Multicast Group Members:

enter the Maximum Multicast Group Members.

Page 123 / 168

120

Fast leave:

check to determine whether to support fast leave. If this value is enabled, IGMP proxy

removes the membership of a group member immediately without sending an IGMP membership

query on downstream. This is very helpful if user wants fast channel (group change) changing in

cases like IPTV environment.

LAN to LAN (Intra LAN) Multicast:

check to determine whether to support LAN to LAN (Intra LAN)

Multicast. If user want to have a multicast data source on LAN side and he want to get IGMP

snooping enabled, then this LAN-to-LAN multicast feature should be enabled.

Page 124 / 168

121

Wireless

This section provides you ways to configure wireless access. When you click this item, the column

will expand to display the sub-items that will lead you to configure your router.

Basic

,

Secturity

,

MAC Filter

,

Wireless Bridge

,

Advanced

and

Station Info

are included here.

Page 125 / 168

122

Basic

It let you determine whether to enable Wireless function and set the basic parameters of an AP and

the Virtual APs.

Enable Wireless:

Default setting is set to Enable. If you do not have any wireless devices, check

the checkbox again to unselect.

Hide Access Point:

It is function in which transmits its SSID to the air so that when wireless client

searches for a network, router can then be discovered and recognized. Check the checkbox to

determine whether you want to hide SSID.

Clients Isolation:

if you enabled this function, then each of your wireless clients will not be

communicate with each other.

Wireless multicast Forwarding (WMF):

check to enable or disable wireless multicast forwarding.

SSID:

The SSID is the unique name of a wireless access point (AP) to be distinguished from another.

For security purpose, change the default wlan-ap to a unique ID name to the AP already built-in to

the router’s wireless interface. It is case sensitive and must not excess 32 characters. Make sure

your wireless clients have exactly the SSID as the device, in order to get connected to your network.

Note:

SSID is case sensitive and must not excess 32 characters.

BSSID:

Basic Set Service Identifier, it is a local managed IEEE MAC address, and is 48 bits value.

Rate

Popular Billion Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share