Page 16 / 100
Scroll up to view Page 11 - 15
Configuring a PC in Windows 2000
1.
Go to
Start / Settings / Control Panel
.
In the Control Panel, double-click on
Network
and Dial-up Connections
.
2.
Double-click
Local Area Connection
.
3.
In the
Local Area Connection Status
window click
Properties
.
4.
Select
Internet Protocol (TCP/IP)
and
click
Properties
.
5.
Select the
Obtain an IP address
automatically
and
the
Obtain DNS
server address automatically
radio
buttons.
6.
Click
OK
to finish the configuration.
14
Page 17 / 100
Configuring PC in Windows 98/Me
1.
Go to
Start / Settings / Control Panel
.
In the Control Panel, double-click on
Network
and choose the
Configuration
tab.
2.
Select
TCP/IP ->NE2000 Compatible
,
or the name of your Network Interface
Card (NIC) in your PC.
3.
Select the
Obtain an IP address
automatically
radio button.
4.
Then select the
DNS Configuration
tab.
5.
Select the
Disable DNS
radio button
and click
OK
to finish the configuration.
15
Page 18 / 100
Configuring PC in Windows NT4.0
1.
Go to
Start / Settings / Control Panel
. In
the Control Panel, double-click on
Network
and choose the
Protocols
tab.
2.
Select
TCP/IP Protocol
and click
Properties
.
3.
Select the
Obtain an IP address from a
DHCP server
radio button and click
OK
.
16
Page 19 / 100
3.2 Factory Default Settings
Before configuring the BiPAC 7300(G) router, you need to know the following default
settings.
Web Interface:
Username: admin
Password: admin
LAN Device IP Settings:
Subnet Mask: 255.255.255.0
ISP setting in WAN site:
PPPoE
DHCP Server:
DHCP server is enabled.
Start IP Address: 192.168.1.100
IP pool counts: 100
3.2.1 Username and Password
The default username and password are “
admin
” and “
admin
” respectively.
Attention
To reset the router or to restore it to factory default settings press the
Reset button using the end of paper clip or other small pointed object.
1. To perform Failure recovery for a dead router:
Simply hold the Reset button when powering on the router and
download an application if necessary.
2. To perform recovery in case of a misplaced Password:
Hold the Reset button until the LEDs all turn Off, turn On and then turn
Off. The router performs configuration factory reset and the router
reboots. You can then access the router from the web GUI.
17
Page 20 / 100
3.3 LAN and WAN Port Addresses
The parameters of LAN and WAN ports are preset at the factory.
The default values are
shown below.
IP address
192.168.1.254
Subnet Mask
255.255.255.0
DHCP server function
Enabled
IP addresses for
distribution to PCs
100 IP addresses continuing from
192.168.1.100 through
192.168.1.199
The PPPoE function is
enabled
to
automatically get the
WAN port
configuration from the
ISP, but you have to
set the username and
password first.
3.4 Configuring with your BiPAC 7300(G)
1. To configure this device, you must have IE 5.0 / Netscape 4.5 or
above installed
2. You may configure the router for Internet access in two ways:
(A) Easy Sign-On (EZSO)
(B) Web Configurator
Easy Sign On:
User just installs all of cables and uses the browser to surf Internet. At this time, the EZSO
WEB GUI will be popped up and request you to input some basic information you get from
ISP. After this, you can surf Internet right away.
18
19216811.live