Billion BiPAC-7300G-RA Router Manual PDF (Setup & Configuration Guide)

Page 11 / 100 Scroll up to view Page 6 - 10

2.4The Rear Ports

BiPAC 7300

1

3

4

2

BiPAC 7300G

4

3

5

1

2

1

PWR

Connect the supplied power adapter to this jack.

2

RESET

After the router is powered on, press this recessed button using

the end of paper clip or other small pointed object to reset the

router or to restore it to factory default settings.

1. Recovery procedures for non-working routers (e.g. after a

failed firmware upgrade flash):

Hold the

Emergency/Failure Recovery Button

on the back of the

modem in. Keep this button held in and turn on the modem. Once

the lights on the modem have stopped flashing, release the

Emergency/Failure Recovery Button.

The modem's

emergency-reflash web interface will then be accessible via

http://192.168.1.254/ where you can upload a firmware image to

restore the modem to a functional state. Please note that the

modem will only respond via its web interface at this address,

and will not respond to ping requests from your PC or to telnet

connections.

2. Recovery procedures for a lost web interface password:

After turning the router on press the

Emergency/Failure

Recovery Button

on the back of the modem, and hold the button

in until all lights on the modem flash and it reboots with factory

9

Page 12 / 100

default settings. The login will be reset to

admin

and the

password will be reset to

admin

, and the modem will be

accessible via its default IP address at http://192.168.1.254/

3

LAN

Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the

four LAN ports when connecting to a PC or an office/home

network of 10Mbps or 100Mbps.

4

ADSL

(LINE)

Connect the supplied RJ-11 (telephone) cable to this port when

connecting to the ADSL/telephone network.

5

Power

Switch

Power ON/OFF switch.

The detail instruction in Emergency/Failure Recovery Button

1. Recovery procedures for non-working routers (e.g. after a failed firmware upgrade flash):

Hold the

Emergency/Failure Recovery Button

on the back of the modem in. Keep this button

held in and turn on the modem. Once the lights on the modem have stopped flashing,

release the

Emergency/Failure Recovery Button.

The modem's emergency-reflash web

interface will then be accessible via

http://192.168.1.254/

where you can upload a firmware

image to restore the modem to a functional state. Please note that the modem will only

respond via its web interface at this address, and will not respond to ping requests from your

PC or to telnet connections.

2. Recovery procedures for a lost web interface password:

After turning the router on press the

Emergency/Failure Recovery Button

on the back of the

modem, and hold the button in until all lights on the modem flash and it reboots with factory

default settings. The login will be reset to

admin

and the password will be reset to

admin

, and

the modem will be accessible via its default IP address at

http://192.168.1.254/

Before powered on the router to enter the recovery process. please

configure the IP address of the PC as 192.168.1.1 and process step by

step.

1. Power the router off.

2. Hold the " Emergency/Failure Recovery Button”.

3. Power on the router. Then Router's IP will reset to Default (Say

192.168.1.254)

4. Download the firmware.

10

Page 13 / 100

2.5 Cabling

Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper

ables.

and

und can

ause problems with your ADSL connection, including frequent disconnections.

One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that

all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that

the LAN

c

Ensure that all other devices connected to the same telephone line as your Billion router (e.g.

telephones, fax machines, analog modems) have a line filter connected between them

the wall socket (unless you are using a Central Splitter or Central Filter installed by a

qualified and licensed electrician), and ensure that all line filters are correctly installed and

the right way around. Missing line filters or line filters installed the wrong way aro

c

11

Page 14 / 100

Chapter 3

Installation

You can configure the BiPAC 7300(G) router through the convenient and user-friendly

interface of a web browser. Most popular operating systems such as Linux, Mac and

Windows 98/NT/2000/XP/Me include a web browser as a standard application.

3.1 Before Configuration

PCs must have a properly installed Ethernet interface and connect to the router directly or

through an external repeater hub. In addition, PCs must have TCP/IP installed and

configured to obtain an IP address through a DHCP server or a fixed IP address that must be

in the same subnet as the router. The default IP address of the router is

192.168.1.254

and

the subnet mask is

255.255.255.0

(i.e. any attached PC must be in the same subnet, and

have an IP address in the range of 192.168.1.1 to 192.168.1.253). The easiest way is to

configure the PC to obtain an IP address automatically from the router using DHCP. If you

encounter any problems accessing the router’s web interface you are advised to

uninstall

any kind of software firewall on your PCs, as they can cause problems accessing the

192.168.1.254 IP address of the router.

Please follow the steps below for installation on your PC’s network environment. First of all,

check your PC’s network components. The TCP/IP protocol stack and Ethernet network

adapter must be installed. If not, please refer to your Windows-related or other operating

system manuals.

Any TCP/IP capable workstation can be used to communicate with or

through the BiPAC 7300(G). To configure other types of workstations,

please consult the manufacturer’s documentation.

12

Page 15 / 100

Configuring a PC in Windows XP

1.

Go to

Start / Control Panel (in Classic

View)

. In the Control Panel, double-click

on

Network Connections

2.

Double-click

Local Area Connection

.

3.

In the

Local Area Connection Status

window, click

Properties

.

4.

Select

Internet Protocol (TCP/IP)

and

click

Properties

.

5.

Select the

Obtain an IP address

automatically

and

the

Obtain DNS

server address automatically

radio

buttons.

6.

Click

OK

to finish the configuration.

13

Rate

Popular Billion Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share