Page 36 / 67 Scroll up to view Page 31 - 35
VPI
:
The valid range for the VPI is 0 to 255. Enter the VPI assigned to you. This field may
already be configured.
VCI:
The valid range for the VCI is 32 to 65535. Enter the VCI assigned to you. This field
may already be configured.
ATM QoS:
Select
CBR
to specify fixed (always-on) bandwidth for voice or data traffic.
Select
UBR
for applications that are non-time sensitive, such as e-mail. Select
VBR
for burst
traffic and bandwidth sharing with other applications.
PCR:
Divide the DSL line rate (bps) by 424 (the size of an ATM cell) to find the Peak Cell
Rate (PCR). This is the maximum rate at which the sender can send cells.
SCR:
The Sustain Cell Rate (SCR) sets the average cell rate (long-term) that can be
transmitted.
MBS:
Maximum Burst Size (MBS) refers to the maximum number of cells that can be sent
at the peak rate. Type the MBS, which is less than 65535
Encapsulation:
ISP:
Select the encapsulation type your ISP uses from the
Encapsulation
list.
Choices vary depending on what you select in the
Mode
field.
If you select
Bridge
in the
Mode
field, select
1483 Bridged IP
.
If you select Routing in the Mode field, select PPPoA, 1483 Bridged IP, 1483 Router IP or
PPPoE.
PPPoE/PPPoA
User Name:
Enter the user name exactly as your ISP assigned.
Password:
Enter the password associated with the user name above.
Encapsulation:
select Bridge in the Mode field, select either PPPoA or RFC 1483.
select Routing in the Mode field, select PPPoA, RFC 1483, ENET ENCAP or PPPoE.
Multiplex: Select the method of multiplexing used by your ISP. Choices are VC or LLC.
Connection:
The schedule rule(s) have priority over your Connection settings.
Always on
: Select Always on Connection when you want your connection up all the time.
Connect on Demand:
Select Connect on Demand when you don't want the connection up
all the time and specify an idle time-out in the Max Idle Timeout field
Get IP Address:
Choose Static or Dynamic
Static IP Address:
Enter the IP address of ADSL Router in dotted decimal notation, for
example, 192.168.1.254 (factory default).
IP Subnet Mask:
The default is 255.0.0.0. User can change it to other such as
255.255.255.0.Type the subnet mask assigned to you by your ISP (if given).
Gateway:
You must specify a gateway IP address (supplied by your ISP) when you use
1483 Bridged IP
in the
Encapsulation
field in the previous screen.
34
Page 37 / 67
Network Address Translation:
Select
None
,
Many to One
or
Many to Many
from the
drop-sown list box. Refer to the NAT chapter for more details.
Dynamic Route:
RIP Version:
Select the RIP version from RIP-1, RIP-2B and RIP-2M.
RIP Direction:
Select the RIP direction from None, Both, In Only and Out Only.
Multicast:
IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to
establish membership in a Multicast group - it is not used to carry user data. The BiPAC
5200 Series supports both IGMP version 1 (IGMP-v1) and IGMP-v2. Select None to disable
it
35
Page 38 / 67
4.2.2 LAN
A Local Area Network (LAN) is a shared communication system to which many computers
are attached and is limited to the immediate area, usually the same building or floor of a
building.
Router Local IP
IP Address:
Enter the IP address of ADSL Router in dotted decimal notation, for example,
192.168.1.254 (factory default).
IP Subnet Mask:
The default is 255.0.0.0. User can change it to other such as
255.255.255.0.Type the subnet mask assigned to you by your ISP (if given).
Dynamic Route:
Select the RIP version from RIP-1, RIP-2B and RIP-2M.
RIP Direction:
Select the RIP direction from None, Both, In Only and Out Only.
Multicast:
IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to
establish membership in a Multicast group - it is not used to carry user data. The BiPAC
5200 Series supports both IGMP version 1 (IGMP-v1) and IGMP-v2. Select None to disable
it
36
Page 39 / 67
DHCP
DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual
clients to obtain TCP/IP configuration at start-up from a server.
DHCP:
If set to
Enable
, your BiPAC 5200 Series can assign IP addresses, an IP default gateway
and DNS servers to Windows 95, Windows NT and other systems that support the DHCP
client.
If set to
disabled
, the DHCP server will be disabled.
If set to
Relay
, the BiPAC 5200 Series acts as a surrogate DHCP server and relays DHCP
requests and responses between the remote server and the clients. Enter the IP address of
the actual, remote DHCP server in the Remote DHCP Server field in this case.
When DHCP is used, the following items need to be set.
Starting IP Address:
This field specifies the first of the contiguous addresses in the IP
address pool.
IP Pool Count:
This field specifies the size or count of the IP address pool.
Lease Time:
The current lease time of client.
Primary DNS Server:
Enter the IP addresses of the DNS servers. The DNS servers are
passed to the DHCP clients along with the IP address and the subnet mask.
Secondary DNS Server:
Enter the IP addresses of the DNS servers. The DNS servers
are passed to the DHCP clients along with the IP address and the subnet mask.
37
Page 40 / 67
4.3 Advanced Setup
4.3.1 Firewall
Your router includes a firewall for controlling Internet access from your LAN and helping to
prevent attacks from hackers. In addition to this, when using NAT (Network Address
Translation) the router acts as a “natural” Internet
firewall, since all PCs on your LAN use
private IP addresses that cannot be directly accessed from the Internet.
Firewall:
~
Enabled:
As set in default setting
,
it activates your firewall function.
~
Disabled:
, it disables the firewall function.
38

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top