1. Home
    2. /
  2. Manuals
    3. /
  3. Bell
    4. /
  4. CellPipe-7130
    5. /
  5. 3
Page 11 / 24 Scroll up to view Page 6 - 10
11
How to set an admin password
An admin password is used for security. Once set, you will need to enter it
before making any changes to your settings. Before you can access the
Wireless Access Point device, you must first determine which IP address has
been assigned. To identify what the IP address is:
1.
Open your web browser.
2.
Type
in the address bar, and then press
Enter
. If you are
prompted to enter in a username and password, these are set to the
following defaults:
Username
: admin
Password
: admin
3.
Select
Device Table
from the left menu. In this Device Table, note down the
IP address indicated for
WAP610N
. You will need this IP address to
continue.
4.
Close and then re-open your web browser.
5.
Type
where X is the last number in the IP address of the
WAP610N
device. Then press
Enter
. If you are prompted to enter in a
username and password, these are set to the following defaults:
Username
: admin
Password
: admin
FibeRG_0110_ENG_V3
11
05/02/10
10:34 AM
Page 12 / 24
12
6.
Click the
Administration
tab and then select
Management
.
7.
Enter a new password in the
Access Point Password
box and then type it
again in the
Re-enter to confirm
box.
8.
Click
Save Settings
.
FibeRG_0110_ENG_V3
12
05/02/10
10:34 AM
Page 13 / 24
13
How to change existing wireless
settings
Before you can access the Wireless Access Point device, you must first
determine which IP address has been assigned. To identify what the IP
address is:
1.
Open your web browser.
2.
Type
in the address bar, and then press
Enter
. If you are
prompted to enter in a username and password, these are set to the
following defaults:
Username
: admin
Password
: admin
3.
Select
Device Table
from the left menu. In this device table, note down the
IP address indicated for
WAP610N
. You will need this IP address to
continue.
4.
Close and then re-open your web browser.
5.
Type
where X is the last number in the IP address of the
WAP610N
device. Then press
Enter
. If you are prompted to enter in a
username and password, these are set to the following defaults:
Username
: admin
Password
: admin
FibeRG_0110_ENG_V3
13
05/02/10
10:34 AM
Page 14 / 24
14
2.
Ensure the following settings are used:
Wireless Band
:
2.4 GHz
Network Mode
:
Mixed
Channel Width
:
40 MHz only
3. Click
Save Settings
.
If you’ve changed the administrative password, you must use this one in place
of “admin” for the password.
6.
Click the
Wireless
Tab, then select
Basic Wireless Settings
.
There are two ways to configure the Wireless Access Point device’s settings:
-
Manual
-
WiFi Protected Setup
To manually configure your wireless network:
1.
For the
Configuration View
select
Manual
.
FibeRG_0110_ENG_V3
14
05/02/10
10:34 AM
Page 15 / 24
15
To configure your wireless network using WiFi Protected Setup:
If you have client devices, such as wireless adapters that support WiFi
Protected Setup then you can use this feature to configure wireless security
for your network.
There are 3 methods available, use the method that applies to the client
device you are configuring:
1.
Use WiFi Protected Setup button:
-
Click or press the
WiFi Protected Setup
button on the client device.
-
Within a few minutes, click the
WiFi Protected Setup
button on the
setup screen that appears.
-
After the client device has been configured, click
OK
.
-
The WiFi Protected Setup Status, Wireless Band, Network Name (SSID),
and Security method are displayed at the bottom of the screen.
2.
Enter WiFi Protected Setup PIN from client device:
Use this method if your client device has a WiFi Protected Setup PIN
number.
-
Enter the PIN number in the field on the screen that appears.
-
Click
Register
.
-
After the client device has been configured, click
OK
. Then refer back
to your client device or its documentation for further instructions.
-
The WiFi Protected Setup Status, Wireless Band, Network Name (SSID),
and Security method are displayed at the bottom of the screen.
3.
Enter WiFi Protected Setup PIN from access point on client device
Use this method if your client device requests the Access Point’s PIN
number.
-
On the
client’s
WiFi Protected Setup screen, enter the PIN number
listed on the
Access Point’s
WiFi Protected Setup screen. Then click
Register
or the appropriate button. (The PIN number is also listed on
the label on the bottom of the Wireless Access Point device).
-
After the client device has been configured, click
OK
. Then refer back
to your client device or its documentation for further instructions.
-
The WiFi Protected Setup Status, Wireless Band, Network Name (SSID),
and Security method are displayed at the bottom of the screen.
FibeRG_0110_ENG_V3
15
05/02/10
10:34 AM

Rate

4 / 5 based on 3 votes.

Popular Bell Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top