Axesstel MV410r Router Manual PDF (Setup & Configuration Guide)

Page 21 / 58 Scroll up to view Page 16 - 20

20

1.5

Click “OK”.

Step 2

│

Connecting the Modem to your PC

2.1.

Turn off both the EV-DO modem and your PC.

2.2.

Connect the included USB Cable to the USB port on your PC.

2.3.

The Modem cable select switch, located between Ethernet and USB

connectors, should be set to USB.

2.4.

Connect other end of the USB Cable to USB port on the Modem.

2.5.

Connect the included Power Adapter to Power connector of EV-DO modem.

2.6.

Connect the other end of Power Adapter to an electrical outlet.

2.7.

Power on EV-DO modem.

Page 22 / 58

21

Step 3

│

Window Device Setup

3.1

Power ON the PC. After the boot-up process, you will see “Found New

Hardware” screen appears. Select Next to install USB

3.2

Select “Continue Anyway”.

3.3

Press “Finish” to complete the process.

Page 23 / 58

22

3.4

Axesstel Diagnostic Port

will be detected on your PC. Select Next to

install.

3.5

Select “Continue Anyway”.

3.6

Press “Finish” to complete the process.

Page 24 / 58

23

Connecting to Data Service with USB connection

After USB driver has been installed, you must use AxessManager

to configure

and connect the Modem to the network. Please refer to AxessManager

Operational Guide chapter for detailed instructions. Make sure the Modem

selector switch is set to USB position before attempting the connection.

Normally Windows OS will automatically detect your Modem USB connection after

you have installed AxessManager

. If for some reasons Windows OS failed to

complete this task, you may need to perform the following steps after installing

AxessManager

to fully configure your Modem in USB mode.

1.

Verify in Network Connection window that

USB connection has been created in “Dial

up” section. The connection name is set by

your service provider (default name is

1xEvDO). You can also find the connection

name in AxessManager utility, USB

Connection Profile tab

2.

If no USB connection appears in Dial up

section, go to AxessManager utility, USB

Connection Profile tab, highlight the

connection name your service provider has

created, click

Edit

and

OK

to accept the

setup. This will add the connection to the

Network Connection window.

3.

In very rare cases, Windows OS may

associate the wrong modem to your Dial up

connection. To verify, right click on the Dial

up connection name in step 1 above and

select

Properties

. You should see the

Axesstel USB Modem selected and the

correct dial number entered. If not, update

the fields with correct value.

Page 25 / 58

24

Connection Using Ethernet (RJ45) Ports

Although the Modem comes with drivers and enabling software, you don’t have to

install and use them if you simply want to connect to the Internet through the

Ethernet (RJ-45) ports, assuming that your Modem has been activated with the

network

If you have MV400R-series, first go to AxessManager Operation Guide to

authenticate and configure your RUIM (if needed) before returning to the below

instructions.

Configuring Your PC

The Modem’s Ethernet is configured with DHCP by default. This means that IP

address of your PC is automatically assigned by the EV-DO Modem. If for some

reasons, the PC’s cannot get IP address and cannot make connection to Internet,

use the following steps to check the TCP/IP setting of your “Local Area

Connection”.

1. Click the Start button, select Settings,

and select Control Panel. Click on

“Network and Internet Connection” icon.

NOTE:

DHCP stands for Dynamic Host Configuration Protocol. Your Modem has

a built-in DHCP server. The DHCP server will automatically assign an IP

address to the computers on the LAN. Be sure to set each client PC’s

TCP/IP settings to “obtain an IP address automatically”.

Rate

Popular Axesstel Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share