Page 6 / 26 Scroll up to view Page 1 - 5
CDMA 1xEV-DO Wireless Broadband Modem
AXW-D800 / AXW-D1900
- 6 -
Connecting the World Now
Safety Precaution
1. Avoid placing the unit in a dusty location, or near a source of gas or fire.
2. Do not shake, hit or drop the unit.
3. To clean the unit, use only a soft, dry cloth. The chemicals in alcohol,
benzine or acetone can damage the surface of the unit.
4. Do not twist or pull the cord out of the unit.
5. Do not disassemble the phone.
6. DO NOT use the power adapter if the power cord is damaged or the
unit has been dropped or damaged in any way.
7. Only use the power adaptor provided by Axesstel.
Do not use the
Axesstel adapter for any other purpose.
8. Use only the antenna provided with the unit.
Do not use the antenna
for any other purpose.
9. Do not use the unit near water, for example, near a bathtub, sink, wet
basement, or swimming pool.
NOTE: The input voltage and the shape of the plug on this phone may
vary from country to country.
Basic Installation
1. Connect the antennas on the connectors of each side of the unit.
2. Connect the EV-DO modem to computer using RJ-45 Ethernet Cable
(CAT 5) or USB cable.
3. Move the connection selector switch to USB or Ethernet depending on
which cable you are using.
4. Connect the power adaptor to the DC 9V socket of the EV-DO modem.
5. Plug the AC adaptor into an appropriate electrical wall outlet.
Wall mounting…
1. Mark two mounting holes on the wall.
2. Drill two holes at the marked locations.
3. Tighten the screws until the head is about 5mm from the wall.
4. Hang the unit on the screw using the two holes in the back.
5. Push the unit down until the unit is firmly locked into place.
Page 7 / 26
CDMA 1xEV-DO Wireless Broadband Modem
AXW-D800 / AXW-D1900
- 7 -
Connecting the World Now
Getting to know the EV-DO modem
Power Switch
Power Switch is located on the front side of the EV-DO modem.
Turn on the unit by moving switch to ON position (O). Turn off the unit by
moving switch to OFF position (|).
NOTE: When you turn on the EV-DO modem, it automatically searches for
service signal. When it successfully acquires service signal, the
signal LED turns to green, orange or red depending on signal
strength.
Connection Type Switch
Axesstel Wireless 1xEV-DO Modem lets you choose type of connection.
Connection Type Switch is located between Ethernet port and USB port.
Set this switch to Ethernet or USB depending on type of connection you
are using.
LED Indicators
LED
Color
Indicates
Green
Power is on
Power
Off
Power is off
Green
Excellent signal level
Orange
Good signal level
Red
Poor signal level
Signal
Off
No signal or service is present
Green
Connected to the CDMA network
Connect
Off
Not connected
Green
PC connected to the modem by Ethernet
Blinking
Indicates data activity
Ethernet
Off
No PC connected to the modem by Ethernet
Page 8 / 26
CDMA 1xEV-DO Wireless Broadband Modem
AXW-D800 / AXW-D1900
- 8 -
Connecting the World Now
Connection using Ethernet port
1. Power off the unit before connecting the cables.
2. Connect CAT-5 Ethernet cable to Ethernet port of EV-DO Modem.
3. Connection type switch next to the Ethernet port should be set to
Ethernet.
If not, slide the switch toward the Ethernet port.
4. Connect other end of Ethernet cable to the RJ-45 connector of
Ethernet network adapter or a network device.
5. Connect the Power Adapter to the power connector of EV-DO modem.
Plug the AC plug into a power outlet.
6. Turn the power ON, using the power switch next to the power jack.
The LED labeled “Power” light on.
7. Wait for few seconds for EV-DO modem to search for the service.
The
LED labeled “Signal” turns to Red, Orange, or Green when signal is
acquired.
Configuring Your PC
The EV-DO modem’s Ethernet is configured with DHCP by default.
This
means that IP address of your PC is automatically assigned by the EV-DO
modem.
If the PC’s cannot get IP address and cannot make connection to internet.
Check the TCP/IP setting of your “Local Area Connection”.
1. Click the Start button, select
Settings, and select Control
Panel.
Page 9 / 26
CDMA 1xEV-DO Wireless Broadband Modem
AXW-D800 / AXW-D1900
- 9 -
Connecting the World Now
2. Double click the Network
Connection icon.
3. Go to Local Area
Connection Properties.
Page 10 / 26
CDMA 1xEV-DO Wireless Broadband Modem
AXW-D800 / AXW-D1900
- 10 -
Connecting the World Now
4. Select the “Internet Protocol
(TCP/IP)”
1.
If there is no TCP/IP line
listed, you will need to
install TCP/IP first.
5. Press the “Properties”
button.
6. Check “Obtain an IP
address automatically”
7. Check “Obtain DNS Server
address automatically”.
8. Click Ok to exit Properties.
9. If asked to re-start the PC,
click “YES”.

Rate

4.5 / 5 based on 2 votes.

Popular Axesstel Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top