Page 26 / 89 Scroll up to view Page 21 - 25
Step 1
Step 2
Step 3
Step 4
26
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
Touchstone WTM652 Telephony Modem User’s Guide
Mounting the Telephony Modem
You can either mount the Telephony Modem on a wall or place it on a desktop.
For wall-mount applications, you can mount the Telephony Modem with the indi-
cators facing upward (vertical) or to the side (horizontal).
Tools and Materials
For wall-mounted installations, make sure you have the following tools and mate-
rials before proceeding:
for mounting on drywall: Two 1/4” (6mm) drywall anchors and a drill with
1/4” (6mm) bit (not included)
for mounting on plywood or studs: two #6 x 1.5” (38.1 mm) self tapping
screws (not included)
screwdriver (flat-blade or Phillips, depending on what kind of screws you
use)
wall-mount template (included)
transparent tape: for temporarily securing the mounting template to the wall
(not included)
Wall-mounting instructions
1
Position the mounting template on the surface where you intend to mount
the Telephony Modem and secure in place with transparent tape.
2
Drill holes through the template in the specified locations for the mounting
screws. After drilling holes, remove the template from the surface.
3
If using drywall anchors, set them into the wall. Then, drive the screws into
the wall leaving a gap of about 1/8” (3 mm) between the screw head and
the wall. If not using anchors, just drive the screws.
4
Orient the Telephony Modem with the indicator lights facing up or right, as
desired. Slip both mounting slots (in the back of the Telephony Modem) over
the screws, then slide the case down until the narrow end of the keyhole slot
contacts the screw shaft.
5
Proceed to
Connecting the Telephony Modem
.
Page 27 / 89
A
C
B
D
F
E
H
G
27
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
Touchstone WTM652 Telephony Modem User’s Guide
Desktop mounting instructions
1
Position the Telephony Modem so that:
air flows freely around it
the back faces the nearest wall
it will not fall to the floor if bumped or moved
2
Proceed to
Connecting the Telephony Modem
.
Connecting the Telephony Modem
WARNING
Risk of injury or equipment damage
Connecting the Telephony Modem to the home’s existing telephone
wiring should only be performed by a professional installer. Physical con-
nections to the previous telephone provider must be removed and the
wiring must be checked; there must not be any voltage. Cancellation of
telephone service is not adequate. Failure to do so may result in loss of
service and/or permanent damage to the Telephony Modem.
1
Thread the antenna onto the Antenna connector on the back of the Telepho-
ny Modem (
C
). Tighten only by hand. Turn the antenna so that it points
straight up, if possible.
2
Connect one end of the coax cable to the cable outlet or splitter, and the
other end to the Telephony Modem’s Cable connector (
G
). Tighten the con-
nections by hand, then tighten an additional 1/8 turn with a wrench.
Note
: For best performance, use high-quality coax cable and minimize or
eliminate splitters between the cable jack and the Telephony Modem.
3
Insert the plug from the power cord into the Power connector on the back
of the Telephony Modem (
H
) and insert the power cord into a convenient AC
outlet.
The Power light on the front of the Telephony Modem lights up, then flashes
once (refer to the LED table on page 44). See
Troubleshooting
if the Power
light does not turn on.
Page 28 / 89
4
Connect one end of the Ethernet cable to any Ethernet port on the back of
the Telephony Modem, (
D
) and the other end to the Ethernet port on a com-
puter, hub, or broadband router.
Note
: If you are connecting to a computer, use the Ethernet cable included
in the Telephony Modem package.
5
Connect one end of the telephone cable to the telephone port on the back
of the Telephony Modem (
A
or
B
). Connect the other end to the telephone.
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
28
Page 29 / 89
2
1
3
29
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
Touchstone WTM652 Telephony Modem User’s Guide
Configuring Your Wireless Connection
The WTM652 ships with a basic factory default configuration that should allow you
to immediately access the Internet with a wireless connection. If your computer is
equipped with a 802.11b/g wireless LAN card, you may wish to configure the
WTM652 wireless settings. At a minimum, ARRIS suggests that you configure se-
curity settings.
Requirements
Make sure you have the following before attempting to configure your Ethernet con-
nection:
Computer with:
Ethernet interface or wireless interface
Ethernet cable, if using Ethernet interface (supplied)
Web browser
Configuration Basics
The WTM652 uses a web-based interface to configure wireless settings. The follow-
ing screen shows the various components of the interface.
1
Access bar: Shows the WTM652 connection status and provides the follow-
ing links:
Home
— returns to the Status page (shown above) from any screen.
Help
— displays help for the current screen.
Login/Logout
— allows access to screens other than the Status screen.
2
Navigation menu: Select any of the items in this list to display an associated
submenu. Selecting submenu items displays the associated screen. If you
are not logged in, the WTM652 displays the login screen before allowing you
to proceed.
3
Display area: Enter or view configuration information in this area. A
?
link
may be available to explain the purpose of the screen or individual items on
the screen.
Page 30 / 89
Accessing the Configuration Interface
Follow these steps to access the configuration interface. You should have already set
up the WTM652 as described in
Installing and Connecting Your Telephony Modem
.
1
Use the connection utility for your operating system to connect to the wire-
less LAN
arris54g
(this is the Telephony Modem’s factory default SSID).
2
In your web browser, open the page
to display the
Status screen:
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
30

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top