Page 51 / 216 Scroll up to view Page 46 - 50
51
Link: Wireless Scan
Your device automatically checks for the best channel to broadcast wireless services. However, in some cases it
may be useful to switch to a different channel (1 through 11, for North America) on which the network will broad-
cast.
This is a frequency range within the 2.4Ghz band. Channel selection depends on government regulated radio fre-
quencies that vary from region to region. Channel selection can have a significant impact on performance,
depending on other wireless activity close to this device. You need not select a channel at any of the computers on
your wireless network. They will automatically scan available channels seeking a wireless device broadcasting on
the SSID for which they are configured.
This scan will disconnect any wireless client devices from the wireless network.
If you want to scan for a different channel on which the device will broadcast, click the
Continue
button.
Page 52 / 216
Administrator’s Handbook
52
Link: Subnets & DHCP
When you click the
Subnets & DHCP
link, the
Subnets & DHCP
page appears.
The Server configuration determines the functionality of your DHCP Settings. This functionality enables the Gate-
way to assign your LAN computer(s) a “private” IP address and other parameters that allow network communica-
tion. This feature simplifies network administration because the Gateway maintains a list of IP address
assignments. Additional computers can be added to your LAN without the hassle of configuring an IP address.
This is the default mode for your Gateway.
Private LAN Subnet
Device IPv4 Address:
The IP address of your Gateway as seen from the LAN
Subnet Mask:
Subnet mask of your LAN
DHCPv4 Start Address:
First IP address in the range being served to your LAN by the Gateway's DHCP
server
DHCPv4 End Address:
Last IP address in the range being served to your LAN by the Gateway's DHCP
server
Public Subnet
Public Subnet Enable
: If you select On from the pull-down menu, you can enable a second subnet to distrib-
ute public addresses to DHCP clients; this means that IP addresses assigned to LAN clients will be public
addresses
Public IPv4 Address
: The IP address of your Gateway as seen from the WAN
Public Subnet Mask
: Public subnet mask
DHCPv4 Start Address
: First IP address in the range being served from a DHCP public pool.
DHCPv4 End Address
: Last IP address in the range being served from a DHCP public pool.
Page 53 / 216
53
Primary DHCP Pool
: Choose the source of the DHCP pool IP address assignment by selecting either the
Pri-
vate
(local to your LAN) or
Public
(assigned remotely) radio button.
Cascaded Router
Cascaded Router Enable
: If you have another router behind this Gateway, choose
On
from the pull-down
menu.
Cascaded Router Address
: If you chose On from the pull-down menu, enter the IP address of the router you
are using behind this Gateway in the LAN Private IP subnet range.
Network Address
: If you chose On from the pull-down menu, enter the Network Address that defines the
range of IP addresses available to clients of the router you are using behind this Gateway.
Subnet Mask
: If you chose On from the pull-down menu, enter the subnet mask for the Network Address that
defines the range of IP addresses available to clients of the router you are using behind this Gateway.
DHCP
DHCP Lease
: Specifies the default length for DHCP leases issued by the Router. Enter lease time in
dd:hh:mm:ss (days/hours/minutes/seconds) format.
If you make any changes here, click the
Save
button, and if prompted, restart the Gateway.
Page 54 / 216
Administrator’s Handbook
54
Link: HPNA
When you click the
HPNA
link, the
HPNA Network
page appears.
The
HPNA Network
page displays information about the Gateway’s HPNA-connected devices in 15 minute inter-
vals.
If you have two or more stations, you can select the radio button and click the
Set DVR
button to store the
MAC address of the station as the “master DVR.” If the station order subsequently changes, the radio button
will appear on the correct station.
Page 55 / 216
55
You can test the performance of each station to station pair by clicking the
Run extended Test
button. When
you click the
Run extended Test
button, the following page appears as a warning about this invasive test.
If you do not run the Extended Test, the station-to-station performance section is not displayed.
You can generate updated statistics by clicking the
Refresh
button.
Furnished statistics of the current and previous intervals are displayed as follows:
Station ID
HPNA MAC Address
HPNA Firmware (C-coax, T=TP)
HPNA Version
HPNA Master
Interval Start
Interval Stop
Short Tx Pkt
This is the number of Transmitted Packets
Short Rx Pkt
This is the number of Received Packets
CRC Errors Rx
This is the number of Receipt errors
Dropped Tx
This is the number of Transmit packets dropped
Dropped Rx
This is the number of Receipt packets dropped
Tx Error %
This is the percentage of transmitted errors
Rx Error %
This is the percentage of receipt errors
Frames Tx
This is the number of frames transmitted
Frames Rx
This is the number of frames received
Bytes Tx
This is the number of bytes transmitted
Bytes Rx
This is the number of bytes received
Unicast Tx
This is the number of unicast packets transmitted
Unicast Rx
This is the number of unicast packets received
Multicast Tx
This is the number of multicast packets transmitted
Multicast Rx
This is the number of multicast packets received
Local Control Req
This is the number of requests made to the device by local control
Local Control Repl
This is the number of replies made by the device to local control
Remote Control Req
This is the number of requests made to the device by remote control
Remote Control Repl
This is the number of replies made by the device to remote control

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top