1. Home
    2. /
  2. Manuals
    3. /
  3. Arris
    4. /
  4. NVG589 Frontier
    5. /
  5. 31
Page 151 / 216 Scroll up to view Page 146 - 150
151
set physical dsl profile-8c [ on | off ]
Enables or disables VDSL2 profile 8c governing upstream and downstream bandwidth. Default is
on
.
set physical dsl profile-8d [ on | off ]
Enables or disables VDSL2 profile 8d governing upstream and downstream bandwidth. Default is
on
.
set physical dsl profile-12a [ on | off ]
Enables or disables VDSL2 profile 12a governing upstream and downstream bandwidth. Default is
on
.
set physical dsl profile-12b [ on | off ]
Enables or disables VDSL2 profile 12b governing upstream and downstream bandwidth. Default is
on
.
set physical dsl profile-17a [ on | off ]
Enables or disables VDSL2 profile 17a governing upstream and downstream bandwidth. Default is
on
.
set physical dsl profile-30a [ on | off ]
Enables or disables VDSL2 profile 30a governing upstream and downstream bandwidth. Default is
off
.
set physical dsl bit-swap [ on | off ]
Turns DSL bit-swapping on or off. Bit-swapping is resilient to loss of hand-shake commands. Default is
on
.
set physical dsl trellis [ on | off ]
Turns trellis error correction encoding on or off. Default is
on
.
set physical dsl vectoring-enable [ off | on ]
Enables or disables VDSL2 vectoring. Vectoring enables VDSL2 to achieve its highest potential data rates,
exceeding 100 Mbps. Default is
off
.
set physical dsl vectoring-timeout-ms
milliseconds
If
vectoring-enable
is set to
on
, specifies a timeout interval in milliseconds. Default is
5000
.
set physical dsl nlnm-threshold [ 0 - 480 ]
Specifies the New Low Noise Model (NLNM) value between 0 and 480. Default is
60
.
set physical dsl transport [ atm | ptm | auto | off ]
Sets the DSL transport mode: Asynchronous (
atm
), Packet (
ptm
), Automatic (
auto
), or none (
off
). Default is
ptm
.
set physical dsl atm vcc 1 enable [ off | on ]
Turns
atm
on or off on vcc 1. Default is
on
.
Page 152 / 216
Administrator’s Handbook
152
set physical dsl atm vcc 1 aal-type [ aal5 | aal0pkt | aal0cell ]
Sets the ATM Adaptation Layer type (
aal-type
): AAL5, AAL0-packet, or AAL0-cell. Default is
aal5
.
set physical dsl atm vcc 1 datapath [ phy0fast | phy0interleaved ]
Sets the ATM datapath, Fast Path or Interleaved. Default is
phy0fast
.
set physical dsl atm vcc 1 encap-type [ llcsnap-eth | llcsnap-rtip | llcencaps-ppp
| vcmux-eth | vcmux-ipoa | vcmux-pppoa ]
Specifies the data link encapsulation type. Default is
llcsnap-eth
.
set physical dsl atm vcc 1 vpi [ 0 - 255 ]
Sets the Virtual Path Identifier (
vpi
) for the circuit. Default is
0
.
set physical dsl atm vcc 1 vci [ 32 - 65535 ]
Sets the Virtual Channel Identifier (
vci
) for the circuit. Default is
35
.
set physical dsl atm vcc 2 enable [ off | on ]
Turns
atm
on or off on vcc 2. Default is
on
.
set physical dsl atm vcc 2 aal-type [ aal5 | aal0pkt | aal0cell ]
Sets the ATM Adaptation Layer type (
aal-type
): AAL5, AAL0-packet, or AAL0-cell. Default is
aal5
.
set physical dsl atm vcc 2 datapath [ phy0fast | phy0interleaved ]
Sets the ATM datapath, Fast Path or Interleaved. Default is
phy0fast
.
set physical dsl atm vcc 2 encap-type [ llcsnap-eth | llcsnap-rtip | llcencaps-ppp
| vcmux-eth | vcmux-ipoa | vcmux-pppoa ]
Specifies the data link encapsulation type. Default is
llcsnap-eth
.
set physical dsl atm vcc 2 vpi [ 0 - 255 ]
Sets the Virtual Path Identifier (
vpi
) for the circuit. Default is
8
.
set physical dsl atm vcc 2 vci [ 32 - 65535 ]
Sets the Virtual Channel Identifier (
vci
) for the circuit. Default is
35
.
set physical dsl atm vcc
vcc_num
tx-queue
queue_name
Attaches the egress queue template to the atm vc when the queue type is egress.
set physical dsl atm vcc
vcc_num
rx-queue
queue_name
Attaches the ingress queue to the atm vc when the queue type is ingress.
Page 153 / 216
153
set physical dsl ptm datapath [ phy0fast | phy0interleaved ]
Sets the ATM datapath, Fast Path or Interleaved. Default is
phy0fast
.
set physical dsl ptm priority [ low | high ]
Sets the Packet Transfer Mode (
ptm
) priority. Default is
low
.
set physical dsl ptm tx-queue
queue_name
Attaches the egress queue template to the ptm interface when the queue type is egress.
set physical dsl ptm rx-queue
queue_name
Attaches the ingress queue to the ptm interface when the queue type is ingress.
set physical dsl atm vcc 1 auto-vpi-vci [ on | off ]
Turns Automatic VPI/VCI Detection on or off. If you leave the default
on
, the device will try a series of VPI/VCI
pairs that are commonly used by service providers. When one pair succeeds, the device will use this one for
future connections.
set physical dsl atm vcc 1 vpi-vci-list
vpi_vci_pairs
Specifies the series of VPI/VCI pairs that the device will use to attempt a connection. The default set ("0/35 8/35 0/
43 0/51 0/59 8/43 8/51 8/59") may changed.
set physical dsl atm vcc 1 qos enable [ off | on ]
Turns QoS off or on on the virtual circuit. Default is
off
.
set physical dsl power-save enable [ off | on ]
Turns power saving mode off or on. Default is
off
.
Ethernet interfaces
set physical enet [ 1 - 4 ] mac-addr-override
mac_addr
You can override your Gateway’s Ethernet MAC address with any necessary setting. Some ISPs require your
account to be identified by the MAC address, among other things. Enter your 12-character Ethernet MAC override
address as instructed by your service provider, for example: 12 34 AB CD 19 64
set physical enet [ 1 - 4 ] port media [ auto | 100-fd | 100-hd | 10-fd | 10-hd ]
Sets the Ethernet port’s media flow control: Automatic, 100 Mbps Full-Duplex, 100 Mbps Half-Duplex, 10 Mbps
Full-Duplex, or 10 Mbps Half-Duplex. Default is
auto
.
set physical enet [ 1 - 4 ] port mdix [ auto | on | off ]
Sets the Ethernet port’s crossover detection. Default is
off
.
set physical enet
[ 1 - 4 ] tx-queue
queue_name
Attaches the egress queue template to the ethernet interface when the queue type is egress.
Page 154 / 216
Administrator’s Handbook
154
set physical enet
[ 1 - 4 ] rx-queue
queue_name
Attaches the ingress queue to the ethernet interface when the queue type is ingress.
set physical enet [ 1 - 4 ] port power-save enable ""
Turns power saving mode off or on.
set physical ensw max-age
seconds
Sets the maximum delay on the Ethernet switch in seconds. Default is 300 (5 minutes).
set physical ensw qos-mode [ off | p-bit ]
Sets QoS up on Ethernet switch, classified by priority-bit mapping. Default is
off
. When
p-bit
is selected, packets
will be mapped from their priority (even if untagged) to one of four queues per-port in the Ethernet switch.
See
“
Quality of Ser
vice (QoS) Examples
” on page
207
for more information.
☛
Note
This only applies to packets sent from the host CPU to a switch port; it does not apply to port-to-port
traffic.
set physical ensw p-bit-map
pbit-to-4queue-map
Sets the mapping from the 8 priority-bits to the four queues in the Ethernet switch. The lowest priority queue is “1”,
and the highest priority queue is “4”.
Example:
Mapping is “1 1 2 2 3 3 4 4", where priority bit values 0 and 1 would map to queue 1, and values 2 and
3 would map to queue 2, etc.
Wireless interfaces
set physical wireless enable [ on | off ]
Enables or disables the wireless capability for supported Wi-Fi Gateways. Default is
on
.
set physical wireless standard [ bg | b-only | g-only | bgn | n-only | an | a-only ]
Sets and locks the Gateway into the wireless transmission mode you want:
bg
,
b-only
,
g-only
,
bgn
,
n-only
,
an
, or
a-only
. For compatibility with clients using 802.11b (up to 11 Mbps transmission), 802.11g (up to 20+ Mbps),
802.11a (up to 54 Mbit/s using the 5 GHz band), or 802.11n (from 54 Mbit/s to 600 Mbit/s with the use of four spa-
tial streams at a channel width of 40 MHz), select
B/G/N
. To limit your wireless LAN to one mode or the other,
select
G-only
,
N-only
,
A-only
, or
B-only
, or some combination that applies to your setup. Default is
bgn
.
set physical wireless auto-channel [ off | on ]
Turns auto-channel detection
on
or
off
.
set physical wireless bandwidth [ narrow | wide ]
Specifies whether the Wi-Fi channel is
narrow
or
wide
band. Default is
narrow
in compliance with FCC require-
ments.
Page 155 / 216
155
set physical wireless default-channel [ 1... 11 ]
(1 through 11, for North America) on which the network will broadcast. This is a frequency range within the 2.4Ghz
band. Channel selection depends on government regulated radio frequencies that vary from region to region. The
widest range available is from 1 to 14. Europe, France, Spain and Japan differ. Channel selection can have a sig-
nificant impact on performance, depending on other wireless activity close to this Router. Channel selection is not
necessary at the client computers; the clients will scan the available channels seeking access points using the
same SSID as the client. Defaults to
6
.
set physical wireless power [ 1 - 100 ]
Sets some value lower than 100 percent transmit power if your Gateway is located close to other Wi-Fi Gateways
and causes interference. Defaults to
100
(percent).
set physical wireless mul2uni [ off | on ]
Turns wireless “many-to-one” packet scheduling
off
or
on
. Default is
off
.
set physical wireless ssid 1 enable [ on | off ]
Enables or disables the first (default) Wi-Fi SSID.
set physical wireless ssid 1 name
name
Specifies a name for the first Wi-Fi SSID. Defaults to a unique value per router of the form “ATTxxx”.
set physical wireless ssid 1 access-type [ none | allow | deny ]
Specifies the type of address list for defining MAC address filtering. If set to
allow
, only hosts with the specified
addresses will be permitted to join the WLAN of the specified SSID. If set to
deny
, any hosts except those with the
specified addresses will be permitted to join the specified SSID. Default is
none
.
set physical wireless ssid 1 access-list
mac_address
Specifies the MAC address of devices controlled by MAC address filtering.
set physical wireless ssid 1 hidden [ off | on ]
Enables or disables “closed system mode” for the specified SSID. If set to
on
, the specified SSID will not appear
on client scans. Clients must log into the SSID with the exact SSID name and credentials specified for that SSID.
set physical wireless ssid 1 isolate [ off | on ]
If set to
on
, blocks wireless clients from communicating with other wireless clients on the LAN side of the Gate-
way. Defaults to
off
.
set physical wireless ssid 1 security [ none | wep | wpa ]
Sets the wireless privacy type:
none
,
wep
, or
wpa-psk
. Default is
none
.
set physical wireless ssid 2 enable [ off | on ]
Enables or disables the second available SSID.

Rate

4.5 / 5 based on 2 votes.

Popular Arris Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top