1. Home
    2. /
  2. Manuals
    3. /
  3. Alvarion
    4. /
  4. BMAX-6000 Telrad
    5. /
  5. 12
Page 56 / 138 Scroll up to view Page 51 - 55
BreezeMAX PRO 6000 Product Manual
Chapter 4 - Configuring Setup Parameters
Introduction
36
4.1
Introduction
The BreezeMAX PRO 6000’s Setup menu allows you to implement general management functions for
the unit, including setting connection modes, the system time zone, configuring the device name and
access password, and restore settings to factory defaults.
When you make a configuration change in the Setup pages, the following message is displayed after
clicking Apply: “Configuration setting”. After the configuration is applied, a “Prepare for Reboot”
message is displayed. The system performs a reboot and counts 60 seconds.
When applying Factory Defaults, a "Restore to factory default settings" message appears and then a
Rebooting message and 60 seconds countdown are displayed.
INFORMATION
You can use the web browser interface to access the WAN IP address only if the unit already has an IP
address that is reachable through your network.
The default LAN IP address of the BreezeMAX PRO 6000 is 192.168.254.251. The unit operates by
default in DHCP mode.
Page 57 / 138
BreezeMAX PRO 6000 Product Manual
Chapter 4 - Configuring Setup Parameters
Setting Basic Parameters
37
4.2
Setting Basic Parameters
The Basic Setup allows you to configure the main system parameters.
The following table describes the configurable Basic parameters:
NOTE!
Do not change parameters in this page unless specifically instructed by your service provider. Doing so
may cause your internet/VoIP connection to fail, and you will need to reset the unit to default
parameter values.
Figure 4-1: Setup - Basic Parameters
Table 4-1: Basic Parameters
Parameter
Description
Default
Possible Values
Operation Mode
Operation Mode
Specifies the mode for forwarding
data packets from the service
provider’s WiMAX network to the
local network.
Router
Router (the only option,
unless differently
configured by Alvarion)
Bridge IPCS
Bridge ETHCS
Page 58 / 138
BreezeMAX PRO 6000 Product Manual
Chapter 4 - Configuring Setup Parameters
Setting Basic Parameters
38
Internal Management/VoIP Connection Mode
Management
Connection Mode
Sets the forwarding mode for
sending management packets to
the WiMAX network:
Bridge mode - forwards
packets based on Layer 2
MAC addresses. Bridge mode
means that management
connection has a different IP
than data connection. This IP
is used for communication
with the management server,
for web access from WAN,
ping, etc.
Router mode - forwards
packets based on Layer 3 IP
addresses. Uses data interface
for Management
communication.
Router
Bridge
Router
VoIP Connection
Mode
Sets the forwarding mode for
sending VoIP packets to the
WiMAX network:
Bridge mode forwards packets
based on Layer 2 MAC
addresses. Bridge mode
means that voice connection
has a different IP than data or
management connections.
This IP is used only for
SIP/RTCP and RTP messages
sent and received by the
device’s POTS (plain old
telephone service) lines.
Router mode forwards packets
based on Layer 3 IP addresses.
Uses data interface for VoIP
communication.
None - No forwarding. VoIP
interface is not available.
Router
Bridge
Router
None
Table 4-1: Basic Parameters (Continued)
Parameter
Description
Default
Possible Values
Page 59 / 138
BreezeMAX PRO 6000 Product Manual
Chapter 4 - Configuring Setup Parameters
Setting Basic Parameters
39
Connection Mode
Connection Mode
Sets the connection type for the
unit:
DHCP - The system will assign
IP addresses to the unit on the
wide area network (WAN).
Static - The IP address is
predefined and fixed.
When
you select this option, new
menu items are displayed for
configuration:
»
WAN IP Address
»
WAN Subnet Mask
»
WAN Gateway Address
»
DNS1- Domain Name System
»
DNS2
DHCP
DHCP
Static
WAN MTU
WAN MTU
Sets the WAN maximum
transmission unit (MTU) size in
bytes
Auto (1400) - transmission
unit size is 1400 (maximum)
bytes
Manual - enter the value for
transmission unit size (Range:
576-1500)
Auto
(1400)
Auto (1400)
Manual
INFORMATION
Static IP is not supported by 4Motion equipment.
Table 4-1: Basic Parameters (Continued)
Parameter
Description
Default
Possible Values
Page 60 / 138
BreezeMAX PRO 6000 Product Manual
Chapter 4 - Configuring Setup Parameters
Setting Password
40
4.3
Setting Password
The Password page enables you to change the default password for remote and local access to the
Graphical User Interface (GUI).
1
Enter a new login password (up to 19 characters).
2
Enter the new password again for verification.
3
Click
Apply
.
INFORMATION
It is strongly recommended that you configure your own password. If a password is not configured, the
management interface is not protected and your network security may be compromised since the
default password is not secure.
Keep a record of the password in a safe place, in case you will need to restore it.
Figure 4-2: Setup - Password
To change the login password:

Rate

3.5 / 5 based on 2 votes.

Popular Alvarion Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top