Allied-Data CopperJet-1616-2P Router Manual PDF (Setup & Configuration Guide)

Page 46 / 86 Scroll up to view Page 41 - 45

Chapter 5: Configuring the CopperJet

5.9.4 ZIPB Advanced configuration

Note: You must ensure that ZIPB is in a disabled state before you carry out any

configuration changes. Once you have changed the configuration and clicked on OK,

you can enable ZIPB and changes will be reflected in the configuration. Any changes

made to the configuration while ZIPB is enabled will be ignored.

You can configure the following advanced settings:

LAN interface:

Select the LAN interface that ZIPB will run on. Usually

Ethernet-0

.

WAN interface:

Select the WAN interface that ZIPB will run on. Usually

ppp-0.

LAN IP address spoof method:

Set the LAN IP address spoof method. Once a public IP

address is assigned to the LAN PC, an IP address on the

same subnet as the public IP address must be created and

assigned to the device’s LAN interface. This option

configures how the LAN interface IP address is created.

Click on the

LAN IP address spoof method

drop down list

and select one of the following:

Top of subnet:

Selects the highest available address in the subnet

Bottom of subnet:

Selects the lowest available address in the subnet

Increment:

Increments the assigned IP address by 1

Manual:

Uses the IP address specified in the Manual LAN IP address

field.

Use PPP server address:

Uses the address of your PPP server.

Manual LAN IP address:

Set the manual LAN IP address only if you selected Manual

as your LAN IP address spoof method.

LAN subnet mask selection method:

Set the LAN subnet mask selection method. You can

select one of the following methods:

Natural:

Uses the subnet mask of the assigned IP address

Manual:

Uses the netmask specified in the Manual LAN subnet mask

field

Manual LAN subnet mask

:

Set the manual LAN subnet mask only if you selected

Manual

as your

LAN subnet mask selection method

.

LAN DHCP server lease time

:

Set the LAN DHCP server lease time duration, in seconds,

of DHCP leases on the LAN.

LAN PC power down time:

set the LAN PC power down time duration, in seconds, of

down time before ZIPB assumes that the LAN PC has been

turned off and that the user no longer needs access to the

Internet.

Once you have configured ZIPB, click on the

OK

button.

Note: that the configuration changes will not take effect until ZIPB is set to enabled. Click

on the Enable button at the top of the page.

Page 44

Page 47 / 86

Chapter 5: Configuring the CopperJet

5.9.5 Limitations of ZIPB

If Dynamic ZIPB is enabled, traffic originating from your CopperJet, such as pings or one-

click update requests bound for the Internet, will not receive a reply. This is because traffic

will appear to come from the public IP address and will therefore always be routed back to

the PC that is currently sharing the public IP address. Only responses to traffic originating

from a PC on the LAN can be routed back.

Page 45

Page 48 / 86

Chapter 5: Configuring the CopperJet

5.10 IP Routes

This option allows you to create static IP routes to destination addresses

via an IP interface name or a Gateway address. From the

Configuration

menu, click on

IP routes

. The

Edit Routes

page is displayed:

his page lists the following information about existing routes:

• Whether the route is valid

T

or invalid

• Destination IP address

• Gateway address

• Netmask address

o edit the destination, gateway and netmask address of a route, click in the relevant

o edit the cost and interface setting for the route, click on the

Advanced Options

o delete an existing route, check the

Delete?

box for a specific route and click on

Apply

.

5.10.1 Creating an IP V4 Route

To create an IP V4 Route click on

Create new IP V4 Route

.

omplete the Create IP v4 Route form in order to configure the route.

hen you have typed the details, click on

OK

. The

Edit Routes

page is displayed.

T

text box, update the information then click on

Apply

.

T

hyperlink for a specific route and update the relevant information. Click on

OK

.

T

The

Create new IP V4 Route

page is displayed:

C

W

The table now contains details of the route that you have just created.

Page 46

Page 49 / 86

Chapter 5: Configuring the CopperJet

5.11 DHCP Server

DHCP allows you to dynamically assign IP address to the computers connected to the

Ethernet of the CopperJet. The CopperJet allows multiple DHCP Servers for multiple IP

subnets. Usually, you would only require 1 DHCP Server.

5.11.1 Configuring DHCP Server

To enable the DHCP Server, go to the

Configuration

menu and select

DHCP serve

r.

The

DHCP Server

page is displayed.

Click on the

Enable

button.

By

Add new interface

, select the interface that you want to use and click on

Add

.

Ethernet-0 is only available at the moment!

After you have enabled the DHCP Server (by clicking on the Enable button), you need to

define a DHCP Server subnet(s).

Click on

Create new Subnet…

.

The

Create new DHCP server subnet

page is displayed.

Page 47

Page 50 / 86

Chapter 5: Configuring the CopperJet

This pag

•

Set the subnet for the D

the same subnet used on the

IP interface by selecting

Ethernet-0

.

client that requests the lease, does not ask for a

specific expiry time (43200) the default time (in seconds)

subnet assigns to a

ase does not ask for a

253 addresses by

rver address

OR

•

t Gateway address.

nce yo

s for your DHCP server, click on

OK

.

elete

is allows you to edit all

e allows you to:

HCP Server manually

OR

use

Default lease time:

If the

will be assigned to a lease.

Max lease time:

The maximum time (in seconds) that a

lease if the client requesting the le

specific expiry time (86400).

•

Set the DHCP address range manually

OR

use a default range of

selecting

Use Default Range

.

•

Set your CopperJet to give out its own IP address as the DNS Se

manually set the primary and secondary DNS Server addresses. When

Use Router

as DNS

Server is selected, DNS Relay will be enabled.

Set your CopperJet to give out its own IP address as the defaul

In most situations this is enabled.

u have entered new configuration detail

O

You will return to the DHCP Server page. The DHCP Server subnet is now added. To d

the DHCP Server subnet mark the box

Delete?

and click on

Apply

.

or advanced options click on the

Advanced Options…

hyperlink. Th

F

of the values that were set when the subnet was created. At the bottom of the page, click

on the

Create new DHCP option

link. The

Create DHCP server configuration option

page is

displayed:

Page 48

Rate

Popular Allied-Data Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share